Panasonic LX-TD500 Programming Manual Download Page 175 | Manualshive

Page: 175 / 388

background image

Group

Programming Guide

175

Parameter

[UCD Setting] FWD No Answer

Default

Disable

Value Range

1.

Disable

2.

Enable

Description/Function

Specifies the treatment of the call which is not answered by the
extension in the UCD group within a specified period of time (Call
Forwarding - No Answer Time).

1.

Disable:
The call continues to ring the current destination extension.

2.

Enable:
The system transfers the call to an idle extension in the group.

Reference

• 1.3 System Features (F/G)

– Extension Group

• 1.5 Attended Features (F/G)

– Uniform Call Distribution (UCD)

Parameter

[UCD Setting] Auto LOGOUT Mode

Default

Disable

Value Range

1.

Disable

2.

1-10 times

Description/Function

Specifies the treatment of extensions in a UCD group who do not /
cannot answer the call.
A member extension may be logged-out automatically, if it does
not answer the call for pre-determined times (1-10) consecutively.
If "Disable" is specified, this setting does not function.

Reference

• 1.3 System Features (F/G)

– Extension Group

• 1.5 Attended Features (F/G)

– Uniform Call Distribution (UCD)

«
...
173
174
175
176
177
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: BERG Pages: 12

Sportsman 9921796

Brand: Polaris Pages: 192

Brand: McElroy Pages: 63

Brand: Access Motor Pages: 22

RHINO FUEL INJECTION 700 FI 2008

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 93

Brand: Yamaha Pages: 99

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 112

Kodiak YFM400FWK

Brand: Yamaha Pages: 167

Brand: Yamaha Pages: 193

Kodiak YFM45FAV

Brand: Yamaha Pages: 194

KODIAK 700 YFM70KDXH

Brand: Yamaha Pages: 178

KODIAK 700 YFM70KDHG

Brand: Yamaha Pages: 180

KODIAK Ultramatic

Brand: Yamaha Pages: 185

KODIAK 4X4 Ultramatic

Brand: Yamaha Pages: 185

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands