Panasonic LX-TD500 Programming Manual Download Page 267 | Manualshive

Page: 267 / 388

background image

Features

Programming Guide

267

Voice Mail Command

Voice Mail Commands are used to control the activity of Voice Mail port.
There are the following four Voice Mail Commands:
Leave Message, Get Message, AA (Automated Attendant) Service and VM (Voice Mail)
Service.
A unique code (dialing digits), up to 16 digits, can be assigned to each command.

Parameter

[Integration Code] FWD to VM Busy Tone

Default

7

Value Range

Up to 3 digits consisting of 0-9, or #

Description/Function

Specifies the FWD to VM Busy Tone code.
Sent to the Voice Mail port when the extension dialed is forwarded
to Voice Mail and no other Voice Mail ports are available to accept
the call. (This signals the Voice Mail port, usually an Automated
Attendant, to let the caller leave a message.)

Reference

• 1.3 System Features (F/G)

– Integration, VPS

Parameter

[Integration Code] FWD to Extension Ringback Tone

Default

8

Value Range

Up to 3 digits consisting of 0-9, or #

Description/Function

Specifies the FWD to Extension Ringback Tone code.
Sent to the Voice Mail port when the extension dialed is forwarded
to another, non-voice mail extension.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

Parameter

[Voice Mail Command] Leave Message

Default

H

Value Range

Up to 16 digits consisting of 0-9, , # or H

Description/Function

Specifies the Leave Message command.
This command is transmitted to a VM port when a call is
forwarded, intercepted or rerouted to the VM port.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

«
...
265
266
267
268
269
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Madill Pages: 45

Brand: Can-Am Pages: 144

Brand: Erde Pages: 4

UTV 2x4 Series 11

Brand: Polaris Pages: 108

Brand: Baja Pages: 82

Brand: Kellfri Pages: 16

DewEze 400 Series

Brand: Harper Pages: 75

Brand: Yamaha Pages: 92

Brand: SAFARI Pages: 50

Brand: SVA Pages: 15

Brand: Schmeiser Pages: 28

Brand: Hog Technologies Pages: 87

12 Volt Quad Bike

Brand: Duck Dynasty Pages: 10

Brand: CYBEX gold Pages: 52

Brand: Razor Pages: 16

Brand: Land Pride Pages: 52

2009 Sportsman XP 850

Brand: Polaris Pages: 381

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands