manualshive.com logo in svg

Panasonic LX-TD500, Programming Manual, Page: 245 / 388

Share
Download
Panasonic LX-TD500 Programming Manual Download Page 245

Line

Programming Guide

245

Parameter

Group No.

Default

(Display only)

Value Range

1-128

Description/Function

Displays the Extension Group to which the selected ISDN 
extension port is assigned.

Reference

• 1.8

BRI Port Assignment (P/G)

Parameter

Name

Default

Blank

Value Range

Up to 10 characters consisting of 0-9, A-Z, a-z or the following 
marks: ! # $ %     ( ) + , - / : ; < = > ? @ &.

Description/Function

Specifies the name for the ISDN extension line.

Reference

• 1.17 Display Features (F/G)

– Display, Call Information

Parameter

Tone

Default

Enable

Value Range

1.

Enable

2.

Disable

Description/Function

Specifies whether the system sends the call progress tone to the 
ISDN extension or not.

Reference

None

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments