manualshive.com logo in svg

Panasonic LX-TD500, Programming Manual

The Panasonic LX-TD500 Programming Manual is an essential resource for users looking to maximize the features and functionality of their LX-TD500 unit. Easily downloadable and completely free, this comprehensive manual is available for download from our website, ensuring effortless access to important programming instructions and guidelines.

Share
Download
background image

Configuration

62

Programming Guide

Parameter

[Ext No.1] DN

Default

Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the extension for B1 channel.

Notes

•

This program allows you to assign an extension number to 
each Voice Mail port. Since each port connected to the VPS 
provides two extensions, this enables you to assign extension 
numbers to each port. To reach the Voice Mail system, users 
dial these extension numbers.

•

When you swap DN you already programmed among Jacks, 
you must clear these DNs once.

Reference

• 2.3

Numbering Plan (P/G)

Parameter

[Ext No.1] Group No.

Default

Blank

Value Range

1-128

Description/Function

Specifies the Extension Group (1-128) to which the B1 channel of 
the VPS (DPT) port is assigned.

Note

•

Specifies the extension group (1-128) to which the type of 
extension group, VM or AA, is assigned.

Reference

• 1.3 System Features (F/G)

– Extension Group

• 3.3

Extension Group (P/G)

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

E-TON IXL 40 Owner'S Manual preview
IXL 40
Brand: E-TON Pages: 30
E-TON 2006 Viper 70 Owner'S Manual preview
2006 Viper 70
Brand: E-TON Pages: 36
Eton DXL90 Owner'S Manual preview
DXL90
Brand: Eton Pages: 30
Sealey TBB300 Instructions For preview
TBB300
Brand: Sealey Pages: 4
Dynacraft 24V CARRIAGE Owner'S Manual preview
24V CARRIAGE
Brand: Dynacraft Pages: 31
GMX MOTORBIKES TRACKER 110cc Assembly Manual preview
TRACKER 110cc
Brand: GMX MOTORBIKES Pages: 57
Costway TY327039BK User Manual preview
TY327039BK
Brand: Costway Pages: 7
PRONAR T680 Operator'S Manual preview
T680
Brand: PRONAR Pages: 147
Columbia 1990 Electric Shuttle Service Manual preview
1990 Electric Shuttle
Brand: Columbia Pages: 112
Trail Rover ATV Owner'S Manual preview
ATV
Brand: Trail Rover Pages: 34
Landoll 855 FINISHOLL Series Supplement Operators Manual preview
855 FINISHOLL Series
Brand: Landoll Pages: 10
EBO VW 1350 HB User Manual preview
VW 1350 HB
Brand: EBO Pages: 19
Yamaha RS90NW Owner'S Manual preview
RS90NW
Brand: Yamaha Pages: 110
Yamaha VIKING YXM70VPXK 2016 Owner'S Manual preview
VIKING YXM70VPXK 2016
Brand: Yamaha Pages: 172
Yamaha YFM66FGX Owner'S Manual preview
YFM66FGX
Brand: Yamaha Pages: 180
Clam Polar Trailer LG 7 Manual preview
Polar Trailer LG 7
Brand: Clam Pages: 5
Centaur 2008 Centaur Operator'S Manual preview
2008 Centaur
Brand: Centaur Pages: 56
Thumpstar CHEETAH 150 Owner'S/Operator'S Manual preview
CHEETAH 150
Brand: Thumpstar Pages: 26

Brands by name

Popular brands

Load more brands