Panasonic LX-TD500 Programming Manual Download Page 202

Page: 202 / 388

Line

202

Programming Guide

Parameter

Name

Default

CO001-CO192

Value Range

Up to 10 characters consisting of 0-9, A-Z, a-z or the following
marks: ! # $ % ( ) + , - / : ; < = > ? @ &.

Description/Function

Specifies the name for the trunk line.

Note

•

This is shown on a display PT when receiving a call using
this trunk.

Reference

• 1.17 Display Features (F/G)

– Display, Call Information

Parameter

Incoming Type

Default

(1) DIL: ELCOT/GCOT/LCOT/T1 [GCO]/T1 [LCO] card (2)
DID: DID/T1 [DID] card (3) DID (ISDN): BRI/PRI23 card (4)
TIE: T1 [TIE] card

Value Range

DIL

DID

DID (ISDN)

MDN

TIE

Description/Function

Specifies how the incoming CO call via this trunk line is routed to
the destination in the system.

DIL:
Incoming CO calls are routed by DIL (Direct In Lines) 1:1 or
1:N feature.

DID:
Incoming CO calls are routed by DID (Direct Inward Dialing)
feature.

DID (ISDN):
Incoming CO calls are routed by ISDN DID (Direct Inward
Dialing) feature.

MDN:
Incoming CO calls are routed by ISDN MDN (Multiple
Directory Number) feature.

TIE:
Incoming CO calls are routed by TIE Line feature.

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands