Panasonic LX-TD500 Programming Manual Download Page 189 | Manualshive

Page: 189 / 388

background image

Group

Programming Guide

189

Parameter

[UCD Setting] Supervisor Extension

Default

Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the Supervisor Extension per UCD Group.
The extension specified as the Supervisor Extension can monitor
the number of waiting calls (calls placed in the waiting queue) and
the Login/Logout status of UCD Group members through the
corresponding DSS buttons.

Reference

• 1.3 System Features (F/G)

– Incoming Group

• 1.5 Attended Features (F/G)

– Uniform Call Distribution (UCD)

Parameter

[UCD Setting] UCD Call Waiting

Default

Enable

Value Range

1.

Disable

2.

Enable

Description/Function

This feature is different from regular Call Waiting. This feature (if
enabled) allows UCD group members to hear a Call Waiting tone
when an inside / outside call arrives but all the extensions in the
UCD Group are busy.

Notes

•

To use this feature, this setting must be set to enable.

•

In addition, each extension must enable regular Call Waiting.

Reference

• 1.3 System Features (F/G)

– Incoming Group

• 1.5 Attended Features (F/G)

– Uniform Call Distribution (UCD)

«
...
187
188
189
190
191
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: BERG Pages: 12

Brand: Lynx Pages: 75

TRAIL BOSS 2003

Brand: Polaris Pages: 213

Brand: Neilsen Pages: 12

Onslaught 550 EFI 4X4 EPS

Brand: Bad Boy Pages: 67

Brand: TransTank Pages: 28

Low Loader Trailer

Brand: Futura Pages: 20

Brand: B&P Manufacturing Pages: 6

Brand: Flagro Pages: 28

Brand: U.S. General Pages: 23

Honey Joy TY324116

Brand: Costway Pages: 7

Brand: Columbia Pages: 40

Brand: ODES UTVS Pages: 41

Brand: Jayco Pages: 124

2013 RANGER RZR 570

Brand: Polaris Pages: 152

1995 TRX 400 FW

Brand: Honda Pages: 155

Brand: Yamaha Pages: 112

Brand: Truxta Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands