Panasonic LX-TD500 Programming Manual Download Page 171 | Manualshive

Page: 171 / 388

background image

Group

Programming Guide

171

Parameter

Tenant No.

Default

1

Value Range

1-8

Description/Function

Specifies the tenant (1-8) to which the Extension Group is assigned.

(Required when "Tenant Service" is employed.)

Reference

•1.3 System Features (F/G)

– Tenant Service

• 2.2

Parameter

[Overflow Setting] Destination – Day / Night

Default

Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the destination extension where the call is transferred to
when all extensions in the Extension Group are unavailable or
logged-out in Day / Night mode respectively.

Reference

None

Parameter

[Overflow Setting] Timer

Default

None

Value Range

None, 5-180 s in 5 s increments

Description/Function

Specifies the length of time in seconds the system is to wait before
transferring the call in the waiting queue to the Overflow
Destination.
(Assignable only when "Operator" is specified in "Group Type"
programming.)

Note

•

If "None" is specified, the call is transferred to the Overflow
Destination immediately.

Reference

•1.3 System Features (F/G)

– Operator Group

«
...
169
170
171
172
173
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

DRIFTER 10-0550

Brand: Kolpin Pages: 17

2005-2008 RX500 FA

Brand: Honda Pages: 540

Brand: Honda Pages: 29

650 MUD PRO 2011

Brand: Arctic Cat Pages: 84

Brand: Yamaha Pages: 54

Brand: Massimo Pages: 174

Trail Boss 330 Quadricycle

Brand: Polaris Pages: 119

Wagon with tilt

Brand: Texas Pages: 42

OUTLANDER 6x6 2021 Series

Brand: Can-Am Pages: 204

Brand: Yamaha Pages: 26

Raptor YFM660RS

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 133

Brand: Yamaha Pages: 144

RAPTOR YFM660RP

Brand: Yamaha Pages: 180

Phazer PZ50GTX 2008

Brand: Yamaha Pages: 212

Brand: Yamaha Pages: 110

Brand: Husqvarna Pages: 33

Brand: Husqvarna Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands