Panasonic LX-TD500 Programming Manual Download Page 225

Page: 225 / 388

Line

Programming Guide

225

Key Type

Additional

Parameters

(default)

Description

SINGLE-CO

Trunk Line
No.

Specifies the trunk port physical number (10101 to 31416).

Tone (2)

Specifies the ringer frequency (ring tone type: 1-8) for
incoming calls.

GROUP-CO

Trunk Group
No.

Specifies the Trunk Group number (01 - 48).

Tone (2)

Specifies the ringer frequency (ring tone type: 1-8) for
incoming calls.

LOOP-CO

Tone (2)

Specifies the ringer frequency (ring tone type: 1-8) for
incoming calls.

DSS

EXT.

Specifies the extension number ( 3 or 4 digits).

PHANTOM

EXT.

Specifies the phantom extension number ( 3 or 4 digits).

Ringing (Yes) Specifies whether the extension rings or not when a call to a

phantom button comes in on the extension.

PDN

Tone (2)

Specifies the ringer frequency (ring tone type: 1 - 8) for
incoming calls.

Ringing Type
(Immediate)

Specifies the timing of ringing when a call comes in on the
extension: Immediate, 1-ring Delay, 3-ring Delay, 6-ring
Delay, No Ring

SDN

EXT.

Specifies the PDN owner's extension number (3 or 4 digits).

Tone (2)

Specifies the ringer frequency (ring tone type: 1 - 8) for
incoming calls.

Ringing Type
(Immediate)

Specifies the timing of ringing when a call comes in on the
extension: Immediate, 1-ring Delay, 3-ring Delay, 6-ring
Delay, No Ring

G-FWD

Specifies the Floating Directory Number of the Incoming
Group.

G-LOGIN/
LOGOUT

Specifies the Floating Directory Number of the Incoming
Group.

ONE-TOUCH Dial

Specifies the telephone number or feature access number (up
to 24 digits consisting of 0 - 9, , #, -, P, S or F).

Note

•

P: Pause, S: Secret Dialing, F: Hook Flash

MESSAGE-
OTHER

EXT.

Specifies the extension number or phantom extension
number (3 or 4 digits).

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands