Panasonic LX-TD500 Programming Manual Download Page 131 | Manualshive

Page: 131 / 388

background image

System

Programming Guide

131

Parameter

15. Special dial tone after setting feature

Default

Enable

Value Range

1.

Enable

2.

Disable

Description/Function

If enabled, the system notifies the extension user by sending a
special dial tone (Dial Tone 2) when one or more of the following
features are assigned on his extension.

•

Absent Message Capability

•

Background Music (BGM)

•

Call Forwarding

•

Call Pickup Deny

•

Call Waiting

•

Data Line Security

•

Do Not Disturb (DND)

•

Electronic Station Lockout

•

Executive Busy Override Deny

•

Paging Deny

•

Pickup Dialing

•

Timed Reminder

Also enabled is Dial Tone 4 (indicates that messages are waiting).

Note

•

Dial Tone 3 is not affected by this setting.

Reference

• 4 Tones / Ring Tones (F/G)
• 6.1.3 Tone List (U/M)

Parameter

17. Destination Busy - DISA

Default

Send busy tone

Value Range

1.

Send busy tone

2.

Transferred to IRNA destination

Description/Function

Specifies the treatment of DISA callers when they dial a busy
extension.

Reference

• 1.5 Attended Features (F/G)

– Direct Inward System Access (DISA)

«
...
129
130
131
132
133
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Club Car Pages: 516

2005-2008 RX500 FA

Brand: Honda Pages: 540

Brand: Panther Pages: 16

Brand: TGB Pages: 269

Brand: TGB Pages: 306

Brand: Arctic Cat Pages: 196

Brand: Alpine Pages: 42

Brand: Baja motorsports Pages: 78

Brand: Landoll Pages: 68

Brand: Access Motor Pages: 65

Brand: Suzuki Pages: 50

Brand: SeaCom Pages: 21

Brand: Ifor Williams Trailers Pages: 42

Brand: Kayo Pages: 5

Brand: ReelCraft Pages: 8

Brand: Tracker Off-Road Pages: 68

Brand: Tracker Pages: 156

Challenger 300EX

Brand: TrailMaster Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands