Panasonic LX-TD500 Programming Manual Download Page 164 | Manualshive

Page: 164 / 388

background image

Group

164

Programming Guide

3.2.2

Trunk Group 2/2

Used to assign parameters for each trunk group. Up to 48 trunk groups can be created in the
system.

Parameter

ISDN Progress Tone Mode

Default

Automatic

Value Range

1.

Automatic

2.

Network

3.

PBX

Description/Function

Selects the way to supply the progress tone to an extension when
the extension user makes an outgoing call via ISDN.

1.

Automatic:
If the network provides a progress tone, the system sends the
network progress tone to the caller. If not, the system sends the
PBX progress tone.

2.

Network:
The system sends the network progress tone to the caller under
all conditions.

3.

PBX:
The system sends the PBX progress tone to the caller under all
conditions.

Reference

None

«
...
162
163
164
165
166
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Maverick Sport 1000 2021

Brand: Can-Am Pages: 195

2009 Outlander 500 EFI

Brand: Can-Am Pages: 152

Powermover PM5900

Brand: Ultra-Fab Pages: 18

Brand: Jacobsen Pages: 76

250GKA-2Z Series

Brand: Kandi USA Pages: 16

Brand: Landoll Pages: 62

Brand: Kayo Pages: 33

Brand: KAYO MOTO Pages: 8

Brand: Yamaha Pages: 405

Brand: Yamaha Pages: 293

Brand: Polaris Pages: 179

Brand: Yamaha Pages: 114

Workman 133-3016

Brand: Toro Pages: 8

Grizzly YFM600FWAM

Brand: Yamaha Pages: 164

Brand: Yamaha Pages: 182

Brand: Yerf-Dog Pages: 80

Brand: Toro Pages: 40

Brand: Great Dane Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands