Panasonic LX-TD500 Programming Manual Download Page 191 | Manualshive

Page: 191 / 388

background image

Group

Programming Guide

191

3.5.1

Destination for Incoming Group

You can assign up to 72 extensions or Extension Groups or both per Incoming Group so that
an incoming CO call rings multiple extensions simultaneously.

Parameter

[Destinations] DN

Default

Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies extensions or Extension Groups or both that you are
going to assign to the specified Incoming Group.

Notes

•

DN of VPS port cannot be assigned as a mailbox number and
an Incoming Group destination.

•

Only DN of an extension or FDN of an extension group can
be assigned as an Incoming Group destination.

•

A single extension can be assigned to up to eight different
Incoming Groups at a time.

Reference

• 1.3 System Features (F/G)

– Flexible Numbering

• 2.3

Numbering Plan (P/G)

«
...
189
190
191
192
193
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Panasonic Pages: 2

Brand: Hammerhead Pages: 11

Brand: Hammerhead Pages: 70

GROUND FORCE ELITE

Brand: Razor Pages: 16

Brand: GAS GAS Pages: 63

Brand: Yamaha Pages: 156

Brand: Yamaha Pages: 154

Brand: Access Pages: 72

Brand: MINIMOTO Pages: 33

Brand: J&J Amusements Pages: 272

Brand: TRILECTRON Pages: 7

Brand: Hammerhead Pages: 67

Brand: Taylor-Dunn Pages: 232

Brand: Yamaha Pages: 176

Brand: Yamaha Pages: 156

Brand: Access Motor Pages: 65

Brand: Access Motor Pages: 59

Ditch Witch PR482

Brand: Charles Machine Works Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands