Panasonic LX-TD500 Programming Manual Download Page 300

Page: 300 / 388

Private Network

300

Programming Guide

Parameter

Leading Digit

Default

Blank

Value Range

Up to 3 digits consisting of 0-9 or X

Description/Function

Specifies the leading one, two or three digits of the number for TIE
calls. Used to determine the trunk group for routing a TIE call.

Note

•

"X" can be used as a wild card character which substitutes
any digit in its position.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

Parameter

Digits to delete

Default

Value Range

0-16

Description/Function

Specifies the number of digits to be deleted from the dialed digits.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

Parameter

Number to be added

Default

Blank

Value Range

Up to 20 digits consisting of 0-9

Description/Function

Specifies the dialing number to be added to the dialed digits.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

Parameter

Trunk Group No.

Default

None

Value Range

None, 1-48

Description/Function

Specifies the trunk group hunt sequence to be used when placing a
TIE call.
The sequence is commonly used by all tenants but trunk group will
be skipped if it does not belong to the same tenant as the caller.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands