Panasonic LX-TD500 Programming Manual Download Page 266 | Manualshive

Page: 266 / 388

background image

Features

266

Programming Guide

Parameter

[Integration Code] Extension Disconnection

Default

#9

Value Range

Up to 3 digits consisting of 0-9, or #

Description/Function

Specifies the Extension Disconnection code.
Sent to the Voice Mail port when the caller disconnects. The
Central Office must set a CPC signal to the PBX line for this signal
to work for CO calls.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

Parameter

[Integration Code] Confirmation Tone

Default

9

Value Range

Up to 3 digits consisting of 0-9, or #

Description/Function

Specifies the Confirmation Tone code.
Sent to the Voice Mail port when the Message Waiting Lamp On or
Message Waiting Lamp Off code is dialed successfully.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

Parameter

[Integration Code] FWD to VM Ringback Tone

Default

6

Value Range

Up to 3 digits consisting of 0-9, or #

Description/Function

Specifies the FWD to VM Ringback Tone code.
Sent to the Voice Mail port when the extension dialed is forwarded
to Voice Mail and another VM (Voice Mail) port is able to answer
the call. (This lets the first Voice Mail port, usually an Automated
Attendant, send the call to the other Voice Mail ports.)

Reference

• 1.3 System Features (F/G)

– Integration, VPS

«
...
264
265
266
267
268
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: E-Z-GO Pages: 158

Brand: Polaris Pages: 690

Brand: Trolla Pages: 11

MAVERICK X3 Series 2017

Brand: Can-Am Pages: 155

Brand: Can-Am Pages: 401

Brand: Cectec Pages: 212

Brand: PRONAR Pages: 101

Brand: U-Line Pages: 9

Brand: Baja motorsports Pages: 77

Quad Lander 250

Brand: Sym Pages: 223

Brand: Parklands Pages: 66

Brand: Taylor-Dunn Pages: 232

Brand: Yamaha Pages: 38

Brand: E-TON Pages: 225

Brand: Humbaur Pages: 56

DS 250 2023 Series

Brand: Can-Am Pages: 172

Brand: Snapper Pages: 4

Brand: Snapper Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands