Panasonic LX-TD500 Programming Manual Download Page 107

Page: 107 / 388

System

Programming Guide

107

Parameter

Call FWD Follow Me

Default

Enable

Value Range

Enable

Disable

Description/Function

Enables or disables "Call Forwarding - Follow Me" feature.

Reference

• 4.3.9 Call Forwarding (U/M)

Parameter

Busy Override

Default

Disable

Value Range

Enable

Disable

Description/Function

Enables or disables "Executive Busy Override" feature.

Reference

• 4.3.33 Executive Busy Override (U/M)

Parameter

DND Override

Default

Disable

Value Range

Enable

Disable

Description/Function

Enables or disables "DND Override" feature.

Reference

• 4.3.28 Do Not Disturb (DND) Override (U/M)

Parameter

Busy Override Deny

Default

Enable

Value Range

Enable

Disable

Description/Function

Enables or disables "Executive Busy Override Deny" feature.

Note

•

Executive Busy Override Deny allows the extension user to
prevent Executive Busy Override from being executed by
another extension user.

Reference

• 4.3.34 Executive Busy Override Deny (U/M)

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands