Panasonic LX-TD500 Programming Manual Download Page 203

Page: 203 / 388

Line

Programming Guide

203

Parameter

Incoming Type

Description/Function

<Available selections and the default values per Card Type>

Note

•

In some cases, the default cannot be changed.

Reference

• 1.5 Attended Features (F/G)

– Direct In Lines (DIL)
– Direct Inward Dialing (DID)

• 2.3 ISDN Attended Features (F/G)

– Direct Inward Dialing (DID)

• 3.1 TIE Line Features (F/G)

– TIE Line Service

BRI

DID

LCOT, GCOT,
ELCOT,
T1 (LCO),
T1 (GCO)
T1 (DID)

PRI23

DID(ISDN)/MDN

DID

TIE/DID(ISDN)

Card Type

Selection

Default

DID

DID(ISDN)

TIE

DID(ISDN)

T1(TIE)

DIL/TIE

DIL

DIL/DID

DID

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands