Panasonic LX-TD500 Programming Manual Download Page 132 | Manualshive

Page: 132 / 388

background image

System

132

Programming Guide

Parameter

18. Destination Busy - DID

Default

Send busy tone

Value Range

1.

Send busy tone

2.

Transferred to IRNA destination

3.

Wait till the destination becomes idle

Description/Function

Specifies the treatment of DID callers when they dial a busy
extension.

Reference

• 1.5 Attended Features (F/G)

– Direct Inward Dialing (DID)

• 2.3 ISDN Attended Features (F/G)

– Direct Inward Dialing (DID)

Parameter

19. Destination Busy - TIE

Default

Send busy tone

Value Range

1.

Send busy tone

2.

Transferred to IRNA destination

Description/Function

Specifies the treatment of TIE callers when they dial a busy
extension.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

Parameter

20. Off-hook Monitor

Default

Enable

Value Range

1.

Enable

2.

Disable

Description/Function

Enables or disables "Off-hook Monitor" feature on a system-wide
basis. This feature allows a PT user on a handset call to let other
people around him monitor the call by pressing the SP-PHONE
button.

Note

•

This setting applies to the following PT extensions only:
KX-T7431, KX-T7433, KX-T7436.

Reference

• 1.12 Conversation Features (F/G)

– Off-Hook Monitor

• 4.3.51 Off-Hook Monitor (U/M)

«
...
130
131
132
133
134
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

WILD HP 300 - SERVICE

Brand: GAS GAS Pages: 65

Brand: Suzuki Pages: 139

Brand: Rayco Pages: 88

Wagon with tilt

Brand: Texas Pages: 42

Brand: TGB Pages: 269

Brand: TGB Pages: 306

Brand: Can-Am Pages: 127

Brand: Monzana Pages: 13

Brand: NorthStar Pages: 24

Brand: HAPERT Pages: 45

Sno Pro 120 2013

Brand: Arctic Cat Pages: 61

PROWLER XT 2014

Brand: Arctic Cat Pages: 218

Tow Dolly RM3477

Brand: Roadmaster Pages: 16

Sure-Trac ST6008

Brand: Novae Pages: 15

Brand: Interstate Pages: 36

CF MOTO CFORCE 450

Brand: DFK Pages: 66

Brand: Chillafish Pages: 40

Brand: Power Wheels Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands