Panasonic LX-TD500 Programming Manual Download Page 343 | Manualshive

Page: 343 / 388

background image

Programming Error Messages

Programming Guide

343

E2005

Maximum entry number of System Speed Dialing exceeded.

The system provides up to 1000 / tenant, 2000 / system of System Speed Dialing entries
available to all extension users.

E2006

Cannot change System Speed Dialing Entries Maximum.

Please delete System Speed Dialing entries until there is less than the setting you want.
Then set System Speed Dialing Entries Maximum once again.

E2007

Invalid directory number for manager extension.

Only DN of an extension can be assigned as a manager extension. (FDN cannot be
assigned.)

E2008

Feature number is too long.

Feature numbers "Hundred Block Extension" or "Other PBX" can be set as the leading
1 or 2 digits of the extension number.

E2009

Cannot delete the Hundred Block Extension, which is currently in use as DN or
FDN.

Cannot delete the hundred block number. It's already used as DN or FDN. Please delete
the hundred block number after you remove the registrations of DN or FDN.

E2010

Feature number duplicated.

Feature numbers can be from 1 to 4 digits and shouldn't be any conflicts.
The following are examples of feature number conflicts.
Examples: N and NX, NXX / NM and NML ( NL is allowed.)

E2011

Out of range.

Overflow Timer should be assigned in the range of Second: 5-180.
"None" shows that Overflow Timer doesn't work.

E2012

Trunk group number duplicated.

Each trunk group in the Local Hunt Sequence must have a unique number.

E2013

Invalid directory number for Operator FDN

Only FDN of an extension group and incoming group can be assigned as an Operator
FDN.

E3001

Invalid directory number for intercept destination.

There are seven possible destinations for intercepted calls:
(1) An extension, (2) an external pager (TAFAS), (3) an OGM group,
(4) an extension group, (5) an incoming group, (6) a phantom extension, or (7) an ISDN
extension (except the wild card character "X")

E3002

Invalid directory number for overflow destination.

Only DN of an extension or FDN of an extension group, an incoming group, a phantom
extension or an external pager (TAFAS) can be assigned as an overflow destination.
However, the type of DN / FDN assignable depends on "Group Type."

E3003

Invalid directory number for UCD supervisor extension.

Only DN of an extension can be assigned as UCD supervisor extension.

Error Code

Error Message

Description

«
...
341
342
343
344
345
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Baja motorsports Pages: 77

Brand: FARMA Pages: 36

Brand: Ezytrail Pages: 28

Brand: Yamaha Pages: 32

Brand: Yamaha Pages: 42

Brand: Yamaha Pages: 130

Brand: Yamaha Pages: 136

Brand: Yamaha Pages: 132

YFB250K Timberwolf

Brand: Yamaha Pages: 159

Brand: Yamaha Pages: 214

Brand: KTM Pages: 205

Brand: Jerr-Dan Pages: 104

Pendpac WITTKE RETRO FL

Brand: Labrie Pages: 130

Brand: Yamaha Pages: 409

Brand: ICI Pages: 4

Brand: Baja Pages: 12

2015 WILDCAT SPORT

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands