Panasonic LX-TD500 Programming Manual Download Page 61 | Manualshive

Page: 61 / 388

background image

Configuration

Programming Guide

61

Parameter

Type

Default

None

Value Range

1.

None

2.

TVS75

3.

TVS100

4.

TVS200

5.

TVS80/110/200-1/200-2

6.

TVS300

Description/Function

Specifies the model number of the Panasonic Voice Processing
System which will be connected to the VPS card.

Note

•

Please select "TVS200-1," if HDD (Hard Disk) Software
Version of your TVS200 is 2.00 or later.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

Parameter

Jack No.

Default

(Display only)

Value Range

—

Description/Function

Displays the Jack No. of VPS.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

Parameter

Port No.

Default

Blank

Value Range

1-16 [DLC card] or 1-8 [DHLC card]

Description/Function

Specifies the extension port to which the VPS (DPT) jack is to be
connected.

Notes

•

This program tells the system which extension port is
connected to the Panasonic Voice Processing System.
This allows the system to send the proper Digital Integration
information to these ports.

•

The port number is displayed only when the attribute of the
port is assigned to VPS (DPT).

Reference

• 1.4

Extension Port Assignment (P/G)

«
...
59
60
61
62
63
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: ODES Pages: 92

Double Eagle - Electric

Brand: J&J Amusements Pages: 275

Brand: KTM Pages: 197

POWER WHEELS W4715

Brand: Fisher-Price Pages: 20

Brand: Trail Rover Pages: 34

Brand: Daimler Pages: 90

Brand: Yamaha Pages: 155

GRIZZLY YFM70GPXH

Brand: Yamaha Pages: 174

Brand: Yamaha Pages: 56

Brand: Yamaha Pages: 478

Brand: Yamaha Pages: 173

Brand: Shop fox Pages: 2

Brand: Honda Pages: 65

Brand: Toro Pages: 44

Brand: Morrison Pages: 35

LittleGiant Trailer TLK864

Brand: Lets Go Aero Pages: 21

Brand: Derbi Pages: 194

Brand: Derbi Pages: 339

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands