Panasonic LX-TD500 Programming Manual Download Page 233

Page: 233 / 388

Line

Programming Guide

233

Notes

•

Flexible DSS / PF Key Assignment should be done before executing this copy function.

•

Copy function is not available in the Interactive mode.

Parameter

Paired Extension

Default

—

Value Range

3-4 digits consisting of 0-9

Description/Function

Displays the extension paired with the DSS Console.

Reference

• 1.15 Proprietary Telephone Features (F/G)

– DSS Console

Parameter

[DSS Console 1-8] Port No.

Default

(Display only)

Value Range

Extension port physical number

Description/Function

Displays the extension port to which the DSS Console is connected.

Reference

• 1.15 Proprietary Telephone Features (F/G)

– DSS Console

• 1.4

Extension Port Assignment (P/G)

Parameter

[DSS Console 1-8] Model

Default

T7440

Value Range

T7440

T7441

Others

Description/Function

Specifies the Model No. of DSS Console.

Reference

• 1.15 Proprietary Telephone Features (F/G)

– DSS Console

Parameter

DSS Key

Default

—

Value Range

—

Description/Function

You can enter into "Flexible DSS Key" screen (Section 4.4.1) by

clicking

on this screen.

Reference

• 2.2.3 Flexible Button Assignment (U/M)
• 5.2.1 Station Programming (U/M)

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands