Panasonic LX-TD500 Programming Manual Download Page 213

Page: 213 / 388

Line

Programming Guide

213

Parameter

Card No.

Default

—

Value Range

XXX: YYY [XXX: Card No. (101-314), YYY: Card Type]

Description/Function

Specifies the physical number of the extension card and its type,
which you are going to program.

Reference

• 1.2

Slot Assignment (P/G)

Parameter

Port No.

Default

Value Range

1-n [n= 4 (OPX), 8 (PLC/HLC/SLC/SLC-M), 16 (DLC/DHLC/
ESLC), 24 (T1 [OPX])]

Description/Function

Specifies the extension port which you are going to program.

Note

•

Port Nos. 17-32 will be displayed when "DN" and "Group
No." for "Ext No.2" are assigned in "1.5

VPS (DPT) Port

Assignment (Section 1.5)."

Reference

• 1.4

Extension Port Assignment (P/G)

Parameter

Default

—

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the extension which you are going to program.

Reference

• 2.3

Numbering Plan (P/G)

Parameter

Group No.

Default

(Display only)

Value Range

1-128

Description/Function

Displays the Extension Group to which the selected extension port
is assigned.

Note

•

Default Group No. for Ext. 1001 is 128.

Reference

• 3.3

Extension Group (P/G)

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands