Panasonic LX-TD500 Programming Manual Download Page 243 | Manualshive

Page: 243 / 388

background image

Line

Programming Guide

243

Parameter

FDN

Default

Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the FDN (Floating Directory Number) for the External
Pager.

Reference

• 1.3 System Features (F/G)

– Floating Station

Parameter

BGM

Default

No check

Value Range

1.

No check [Disable]

2.

Check [Enable]

Description/Function

Specifies whether BGM is sent or not when the External Pager is
idle. Whether sound actually comes out of External Pager or not is
controlled by the Manager or Operators.

Reference

• 4.4.2 Background Music (BGM) — External (U/M)

Parameter

BGM Source

Default

MUS1

Value Range

1.

None

2.

MUS1

3.

MUS2

Description/Function

Assigns the External Music Source port to which the External
Pager is connected. To change music sources, you must first select
and apply "None." Then you can select and apply MUS1 or MUS2.

Reference

• 2.8.2 External Music Source (I/M)

Parameter

DN Refer

Default

—

Value Range

—

Description/Function

Displays the list of DNs/FDNs which are already assigned to the
extensions / system resources.

Reference

None

«
...
241
242
243
244
245
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Ski-Doo Pages: 103

Brand: KAYO MOTO Pages: 11

1997 Fourtrax TRX250

Brand: Honda Pages: 155

Brand: Arctic Cat Pages: 64

Brand: Wilson Electronics Pages: 3

Brand: Terra Cat Pages: 12

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 101

Brand: Yamaha Pages: 497

Brand: Yamaha Pages: 683

2008 Outlander 400 EFI

Brand: Can-Am Pages: 599

Brand: Kinroad Pages: 38

Brand: KTM Pages: 197

Brand: YSI Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands