Panasonic LX-TD500 Programming Manual Download Page 207 | Manualshive

Page: 207 / 388

background image

Line

Programming Guide

207

Parameter

Wink Signal Time-out

Default

1024 ms

Value Range

1.

64 ms

2.

128 ms

3.

256 ms

4.

512 ms

5.

1024 ms

6.

2048 ms

7.

4096 ms

8.

8128 ms

Description/Function

Specifies the length of time in milliseconds that the system is to
wait for the Wink Signal after seizing the trunk.

(Assignable only when "Start Signal Type" is set to "Wink"; the
case of the DID card is excluded.)

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

Parameter

Start Signal Type

Default

Wink

Value Range

1.

Immediate

2.

Wink

Description/Function

Specifies the start signal type for a DID and TIE (E&M) trunk.

1.

Immediate:
The system sends the dialing digits to CO after waiting for the
time length determined by "First Dial Timer" in "Card
Properties" screen of the corresponding trunk card.
For information on "Card Properties" screen, please refer to
"Card Type" in Section "1.2

Slot Assignment."

2.

Wink:
The system sends the dialing digits to CO after receiving the
wink signal.

Reference

• 3.1 TIE Line Features (F/G)

– TIE Line Service

• 1.5 Attended Features (F/G)

– Direct Inward Dialing (DID)

«
...
205
206
207
208
209
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Suzuki Pages: 382

Brand: Kinroad Pages: 37

Brand: Toro Pages: 32

Viper 40E (RXL-40E)

Brand: E-TON Pages: 24

SmarTrax John Deere 8770

Brand: Raven Pages: 48

Brand: E-Z-GO Pages: 64

B0-T48-48 Taylor Truck T48

Brand: Taylor-Dunn Pages: 196

Brand: Grizzly Pages: 2

Brand: Grizzly Pages: 4

Brand: Knapen Trailers Pages: 20

Brand: Ace Sports Pages: 78

Brand: Yamaha Pages: 52

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 175

Brand: Ace Sports Pages: 34

Brand: Yamaha Pages: 174

2012 TERRAIN 250

Brand: Ezgo Pages: 76

Brand: Raven Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands