Panasonic LX-TD500 Programming Manual Download Page 60 | Manualshive

Page: 60 / 388

background image

Configuration

60

Programming Guide

4. Assignment of the extension port connected to the TVS.

Select in "Port No." menu the extension port number of the card (DLC / DHLC) to which the
TVS (DPT) jack is to be connected. This menu is displayed only when the attribute of the port
is assigned to "VPS (DPT)" at step 2.
After "Port No." selection, assign "DN" and "Extension Group No." for the port.

Save the data changes by clicking

.

Then set "Port Status" to "INS (In-Service)."
Jack No.1 must be assigned, because the port is used as the channel to control the VPS.

5. Synchronization of the communication between the KX-TD500 System and the TVS.

The KX-TD500 System begins synchronization with the VPS when the step 4 is done.
The "Power" LED of the VPS begins flashing at the same time. The LED will turn on after the
synchronization is completed. It takes for about 30 seconds to 1 minute to be able to use the
VPS system. It depends on the VPS model and the port number you set up.

Parameter

TVS No.

Default

1

Value Range

1- 8

Description/Function

Specifies one of the Panasonic Voice Processing Systems (VPSs)
connected to the KX-TD500 system, which you are going to
program.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

• 1.2

Slot Assignment (P/G)

Parameter

VPS Card

Default

None

Value Range

None, XXX: YYY [XXX: Card No. (101-314), YYY: Card Type]

Description/Function

Specifies the physical number of DLC / DHLC card to which VPS
is connected as extensions.

Note

•

The first DLC/DHLC card will support jacks 1 to 8 of the
first TVS300 system. A second card will support jacks 9 to
12 of the TVS300 system. A third and fourth card are needed
to support a second TVS300 system which is fully
configured.

Reference

• 1.3 System Features (F/G)

– Integration, VPS

• 1.2

Slot Assignment (P/G)

«
...
58
59
60
61
62
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Jianshe Pages: 82

Brand: DETAIL K2 Pages: 38

Brand: CF MOTO Pages: 365

DS Electric 1984

Brand: Club Car Pages: 24

Brand: Polaris Pages: 346

Sportsman 700 HO 2004

Brand: Polaris Pages: 139

eXtreme Sport ES150IIR

Brand: Hammerhead Pages: 67

Brand: Jayco Pages: 100

Brand: Parklands Pages: 101

Brand: ICI Pages: 4

Brand: Landa Pages: 38

Brand: Landa Pages: 101

Brand: Access Motor Pages: 65

CF MOTO CFORCE 625

Brand: DFK Pages: 64

Brand: Yamaha Pages: 841

Stampede 900 2017

Brand: Textron Pages: 237

Brand: PITBULL Pages: 267

SnoCobra Ski System

Brand: Every Season Products Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands