Panasonic LX-TD500 Programming Manual Download Page 79 | Manualshive

Page: 79 / 388

background image

System

Programming Guide

79

(Auto Start Time)

Specifies "Start / End" time of DAY / NIGHT / LUNCH / BREAK service on a day of the week
basis.

(This setting is valid when "Auto mode" is selected in "DAY / NIGHT Switching Mode"
setting.)

Up to six time frames (Day, Night, Lunch-Start, Lunch-End, Break-Start, Break-End) can be
set up on each day of the week.

Parameter

Inter-tenant Calling (1 - 8)

Default

No check

Value Range

1.

No check [Disallowed]

2.

Check [Allowed]

Description/Function

Specifies other tenant numbers to which extensions in this tenant
can make a call.
If no tenant numbers are checked in this field, extension users
within this tenant cannot make a call to extensions in other tenants.
Making calls from one tenant to another is not allowed by default.

Reference

• 1.3 System Features (F/G)

– Tenant Service

Parameter

Day (SUN-SAT)

Default

9:00 AM

Value Range

1.

Disable

2.

12:00-11:59 PM / AM

Description/Function

Specifies the start time for Day Service.

Reference

• 1.3 System Features (F/G)

– Night Service

Parameter

Night (SUN-SAT)

Default

5:00 PM

Value Range

Same as Day

Description/Function

Specifies the start time for Night Service.

Reference

• 1.3 System Features (F/G)

– Night Service

«
...
77
78
79
80
81
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: KAYO MOTOR Pages: 213

Brand: Odes Industry Pages: 73

Jacobsen Groom Master II 88009

Brand: Textron Pages: 116

500 MXU IRS 4X4

Brand: KYMCO Pages: 1

Brand: Land Pride Pages: 132

MAVERICK Trail 2021 Series

Brand: Can-Am Pages: 195

Brand: Yamaha Pages: 52

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands