Panasonic LX-TD500 Programming Manual Download Page 323 | Manualshive

Page: 323 / 388

background image

Maintenance

Programming Guide

323

Warning to the Dealer regarding the System Password

a)

Please thoroughly inform the importance of the password and the dangers involved to
the customer.

b)

Please maintain the secrecy of the password.
Because a person who knows the password can easily take over the control of any PBX
system in the market and he may proceed to commit toll fraud.

c)

Please change the password periodically.

d)

We strongly recommend that you set the system password to 7 digits for maximum
protection against "hackers."

e)

You have to take the following measures to find the system password, when you forget
the password.
Therefore, please never forget the password.

•

If you have the backup system data, you can find the password by loading the backup
system data to your PC and check the Password with programming screen.

•

If you don't have the backup system data, you have to program again or contact
your Panasonic dealers.

The higher the password level (level 1 is the highest) is, the more programming items the
administrator can access as shown in the table below:

: Allowed to access

Programming

Level 1

Level 2

Level 3

Level 4

1. Configuration

2. System

3. Group

4. Line

5. Features

6. Toll Restriction

7. ARS

8. Private Network

9. DID Dial

10. Maintenance

«
...
321
322
323
324
325
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Yerf-Dog Pages: 21

1997 Fourtrax TRX250

Brand: Honda Pages: 155

Brand: Panasonic Pages: 29

Centennial A-130-12R

Brand: Etnyre Pages: 20

Sportsman 800 EFI 4x4 2012

Brand: Polaris Pages: 485

Brand: KTM Pages: 211

Brand: Parklands Pages: 66

Stand-Up SINGLE RIDE-UP Go Series

Brand: Kendon Pages: 20

Brand: ROSSO MOTORS Pages: 17

TrailPro Deluxe

Brand: TransTank Pages: 20

Brand: Massimo Pages: 220

Brand: Precision Pages: 9

Brand: BOMBARDIER Pages: 40

Brand: BOMBARDIER Pages: 46

1987 Citation LS

Brand: BOMBARDIER Pages: 52

Brand: BOMBARDIER Pages: 60

Brand: BOMBARDIER Pages: 92

Brand: BOMBARDIER Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands