Omron GX-AD0471 User Manual Download Page 69 | Manualshive

Page: 69 / 394

Omron GX-AD0471 User Manual Download Page 69

5 - 3

5 EtherCAT Communications

GX-series EtherCAT Slave Unit User’s Manual

5-2 Eth

er

C

A

T

S

la

ve Information

File (ESI File)

5

5-2

EtherCAT Slave Information File

(ESI File)

An EtherCAT Slave Information (ESI) file contains the setting information of an EtherCAT Slave Unit.
Various EtherCAT communications setting can be defined from the ESI files of connected Slave Units
and the network connection information.
ESI files are installed in the configuration tool to create network configuration information.
You can download the network configuration information to the EtherCAT Master Unit to configure the
EtherCAT network.

ESI

files

Network

configuration

information

EtherCAT Master Unit

EtherCAT Slave Units

Configuration tool

Communications are started according to the
communications settings and the network
configuration in the ESI files that are installed.

«
...
67
68
69
70
71
...
»

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments