manualshive.com logo in svg

Omron GX-AD0471, User Manual, Page: 248 / 394

Share
Download
Omron GX-AD0471 User Manual Download Page 248

10   IO-Link Master Unit

10 - 12

GX-series EtherCAT Slave Unit User’s Manual

*1 I/O power supply to devices:

This is the voltage and current value supplied to devices when the communications modes of the ports on the 
IO-Link Master Unit are IO-Link Mode or SIO (DI) Mode. Check the power consumption of the connected 
device and supply the power from the I/O power supply to the IO-Link Master Unit.

Circuit layout

Installation orientation and restrictions

Installation orientation: 6 possible orientations
Restrictions: No restrictions

Protective functions

•

Short-circuit protection for L+ terminal

•

Short-circuit protection for C/Q terminal

Item

Specification

IN communications 
connector

OUT communications 
connector

Power 
supply 
connector

Unit power supply 
24 V

Unit power supply 
0 V

I/O power 
supply 24 V

I/O power 
supply 0 V

Internal 
circuits

I/O 
connector 
1

I/O 
connector 
8

L+
C/Q
DI
L-

L+
C/Q
DI
L-

Non-isolated 
power supply 
circuits

Non-
isolated 
power 
supply 
circuits

IO-Link 
circuits

Isolation 
circuit

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments