Omron GX-AD0471 User Manual Download Page 58

Page: 58 / 394

4 Installation and Wiring

4 - 10

GX-series EtherCAT Slave Unit User’s Manual



Recommended product

The following pin terminals are recommended for the unit power supply cables.

Also, the following screwdriver is recommended for removing pin terminals.

Supply the Unit power supply and the I/O power supply through the same power supply connector.

(Notes) Supply the Unit power supply and the I/O power supply from separate sources.

An M12 connector (A-coding, male) is used for the power supply connector.

The Unit power supply specifications are given below.



Power Supply Connector

Model

Applicable wire size

Crimping tool

Manufacturer

AI0,5-10WH

0.5 mm/AWG20

CRIMPFOX UD6
(Product No. 1204436)
or CRIMPFOX ZA3
series

Phoenix Contact
Co., Ltd.

H0.5/16 orange

0.5 mm/AWG20

Crimper PZ1.5
(Product No. 900599)

Weidmueller Japan Co., Ltd.

Model

Manufacturer

XW4Z-00C

OMRON

IO-Link Master Unit

Item

Specification

Unit power supply voltage

20.4 to 26.4 VDC (24 VDC

−

15%/+10%)

Pin No.

Signal

Description

UNT_P+

Unit power

UNT_P

−

Unit power supply

−

IO_P+

I/O power

IO_P

−

I/O power supply

−

Power supply connector

GX-ILM08C

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Search results

Summary of Contents for GX-AD0471

Reviews:

Omron GX-AD0471, User Manual, Page: 58 / 394

Search results

Summary of Contents for GX-AD0471

Reviews: