manualshive.com logo in svg

Omron GX-AD0471, User Manual, Page: 238 / 394

Share
Download
Omron GX-AD0471 User Manual Download Page 238

10   IO-Link Master Unit

10 - 2

GX-series EtherCAT Slave Unit User’s Manual

10-1 What Is an IO-Link Master Unit?

An IO-Link Master Unit is a slave that has I/O processing functions for IO-Link communications with 
IO-Link devices and I/O processing functions for digital I/O data (ON/OFF signals) with non-IO_Link 
devices.
For an IO-Link Master Unit, processing functions can be assigned for each port to combine different 
types of I/O processing functions.

Also, with IO-Link devices that support digital inputs with Pin 2, the IO-Link Master Unit can 
simultaneously perform both IO-Link communications and receive digital inputs.

A GX-series IO-Link Master Unit connects to IO-Link devices and the EtherCAT Master Unit as shown 
below.

*1 Non-IO-Link devices can also be connected.

10-1-1 Introduction

10-1-2 Connection Configuration for EtherCAT Communications Master 

Unit and IO-Link Devices

GX-series IO-Link Master Unit

IO-Link communications
(4 wires per device)

IO-Link devices

*1

IO-Link devices

*1

M12

M12

EtherCAT

EtherCAT

EtherCAT communications master

Port 1

Port 3

Port 5

Port 7

Port 2

Port 4

Port 6

Port 8

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments