manualshive.com logo in svg

Omron GX-AD0471, User Manual, Page: 260 / 394

Share
Download
Omron GX-AD0471 User Manual Download Page 260

10   IO-Link Master Unit

10 - 24

GX-series EtherCAT Slave Unit User’s Manual

*1 When mounting the M12 Threaded Waterproof Cover on a connector, always tighten it to a torque of 0.39 to 

0.49 N·m.

*2 When mounting a Smartclick Waterproof Cover on a connector, torque management is not required.

The tool for tightening M12 Threaded Connectors is used when tightening to a specified torque.

Smartclick Waterproof Cover

*2

M12

Smartclick con-
nector

PBT

XS5Z-11

Tool for M12 Threaded Connectors

Name and appearance

Model

Torque Wrench

XY2F-0004

Name and appearance

Specification

Connector type

Materials

Model

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments