Home
/
Omron
/
GX-AD0471
/
User Manual

Omron GX-AD0471, User Manual, Page: 250 / 394

Share

Page: 250 / 394

Omron GX-AD0471 User Manual Download Page 250

10 IO-Link Master Unit

10 - 14

GX-series EtherCAT Slave Unit User’s Manual



L/A IN Indicator

This indicator shows the input communications status.
For the indicator specifications, refer to "6-3-1 Status Indicators" in Page 6 - 4.



L/A OUT Indicator

This indicator shows the output communications status.
For the indicator specifications, refer to "6-3-1 Status Indicators" in Page 6 - 4.



RUN Indicator

This indicator shows the operating status of EtherCAT communications.
For the indicator specifications, refer to "6-3-1 Status Indicators" in Page 6 - 4.



ERR Indicator

This indicator provides information on errors.
For the indicator specifications, refer to "6-3-1 Status Indicators" in Page 6 - 4.



UNIT PWR Indicator

This indicator shows the Unit power supply status.



IO PWR Indicator

This indicator shows the I/O power supply status.

Status Indicators

Color

Status

Meaning

Green

Lit.

The Unit power (24 VDC) is currently supplied.

Not lit.

The Unit power is not currently supplied.

Color

Status

Meaning

Green

Lit.

The I/O power (24 VDC) is currently supplied.

Not lit.

The I/O power is not currently supplied.

«
...
248
249
250
251
252
...
»

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments