Omron GX-AD0471 User Manual Download Page 321

Page: 321 / 394

A - 17

A Appendix

GX-series EtherCAT Slave Unit User’s Manual

A-1 Obje

ct Diction

ary

A-1
-5 PDO Mapping Obje

•

Mapping for soft switch command from the EtherCAT Master Unit to Slave Units.

•

Mapping for preset command value setting.

Encoder Input Slave Unit

1700 hex

257th receive PDO Mapping

Sub-index 0: Number of objects
Range:

−

Unit:

−

Default: 02 hex

Attribute:

−

Size: 1 byte (U8)

Access: RO

PDO map: Not possible

Sub-index 1: 1st Output Object to be mapped
Range:

−

Unit:

−

Default: 40200110 hex

Attribute:

−

Size: 4 bytes (U32)

Access: RO

PDO map: Not possible

Sub-index 2: 2nd Output Object to be mapped
Range:

−

Unit:

−

Default: 40200210 hex

Attribute:

−

Size: 4 bytes (U32)

Access: RO

PDO map: Not possible

1701 hex

258th receive PDO Mapping

Sub-index 0: Number of objects
Range:

−

Unit:

−

Default: 02 hex

Attribute:

−

Size: 1 byte (U8)

Access: RO

PDO map: Not possible

Sub-index 1: 1st Output Object to be mapped
Range:

−

Unit:

−

Default: 40110120 hex

Attribute:

−

Size: 4 bytes (U32)

Access: RO

PDO map: Not possible

Sub-index 2: 2nd Output Object to be mapped
Range:

−

Unit:

−

Default: 40110220 hex

Attribute:

−

Size: 4 bytes (U32)

Access: RO

PDO map: Not possible

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Search results

Summary of Contents for GX-AD0471

Reviews:

Omron GX-AD0471, User Manual, Page: 321 / 394

Search results

Summary of Contents for GX-AD0471

Reviews: