manualshive.com logo in svg

Omron GX-AD0471, User Manual, Page: 251 / 394

Share
Download
Omron GX-AD0471 User Manual Download Page 251

10 - 15

10   IO-Link Master Unit

GX-series EtherCAT Slave Unit User’s Manual

10-4  Sp

ecifica

tion
s

10

10
-4-2

  P
a

rt Names and F

unction

s

C/E Indicator

These indicator show the IO-Link communications status and error status.

C/Q Indicator

These indicator show the digital I/O status.

I/O Indicators

Label

Color

Status

Meaning

A

Green

Lit.

IO-Link communications are in progress during operation in 
IO-Link Mode.

Not lit.

•

IO-Link communications are stopped during operation in 
IO-Link Mode.

•

Operation is currently performed in SIO (DI) or SIO (DO) 
Mode.

•

The port is disabled.

Red

Flashing (1-s 
intervals)

There is an IO-Link communications error during operation in 
IO-Link Mode.

Not lit.

•

There are no IO-Link communications errors during operation 
in IO-Link Mode.

•

Operation is currently performed in SIO (DI) or SIO (DO) 
Mode.

•

The port is disabled.

Label

Color

Status

Meaning

B

Yellow

Lit.

•

The Pin-2 input signal is ON during operation in IO-Link Mode.

•

The I/O signal is ON during operation in SIO (DI) Mode or SIO 
(DO) Mode.

Not lit.

•

The Pin-2 input signal is OFF during operation in IO-Link 
Mode.

•

The I/O signal is OFF during operation in SIO (DI) Mode or 
SIO (DO) Mode.

•

The port is disabled.

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments