manualshive.com logo in svg

Omron GX-AD0471, User Manual, Page: 387 / 394

Share
Download
Omron GX-AD0471 User Manual Download Page 387

A - 83

A   Appendix

GX-series EtherCAT Slave Unit User’s Manual

A

-7  V
ersion

 Information

A

A-7 Version Information

The following table shows the correspondence between the unit version of each EtherCAT Slave Unit 
model and the compatible version of Support Software. 
If you use your EtherCAT Slave Unit with the corresponding version or a higher version of Support 
Software, all the functions supported by the unit version of the EtherCAT Slave Unit are available.  
Refer to 

Version Upgrade Information

 on page 16 for details on the functions that have been added or 

changed due to the unit version upgrade of the EtherCAT Slave Units.

EtherCAT Slave Unit 

model

Unit version

Compatible version of Support Software

Sysmac Studio

Cx-ConfiguratorFDT

GX-ID



Ver.1.2

Ver.1.25

−

Ver.1.1

Ver.1.01

−

Ver.1.0

GX-OD



Ver.1.2

Ver.1.25

−

Ver.1.1

Ver.1.01

−

Ver.1.0

GX-OC



Ver.1.2

Ver.1.25

−

Ver.1.1

Ver.1.01

−

Ver.1.0

GX-MD



Ver.1.2

Ver.1.25

−

Ver.1.1

Ver.1.01

−

Ver.1.0

GX-AD



Ver.1.2

Ver.1.25

−

Ver.1.1

Ver.1.01

−

Ver.1.0

GX-DA



Ver.1.2

Ver.1.25

−

Ver.1.1

Ver.1.01

−

Ver.1.0

GX-EC



Ver.1.2

Ver.1.25

−

Ver.1.1

Ver.1.01

−

Ver.1.0

GX-ILM



Ver.1.2

Ver.1.25

Ver.2.2

Ver.1.1

Ver.1.20

Ver.2.2

Ver.1.0

Ver.1.16

Ver.2.2

Summary of Contents for GX-AD0471











































































































































































































































































































































































































Reviews:

No comments