NEC Super Script 4400 Maintenance Manual Download Page 79 | Manualshive

Page: 79 / 317

background image

70

SuperScript 4400 — Maintenance Guide

Unit Status:

Click here to view the current state for each protocol and NIC port available on your NIC. For

each supported protocol (Novell NetWare, TCP/IP, or AppleTalk), the top line displays the protocols
supported and if the protocol is enabled or disabled.

Network Address:

Click here to view the serial number and the Ethernet MAC (Media Access Control)

address for the NIC.

Change Password:

Changing any NIC parameters using the NIC Configuration Menu requires a password.

Click here to change your password. The default password is

sysadm.

Your password can contain letters,

numbers, and punctuation, and is case sensitive.

note:

If you forget your password, you can restore factory defaults manually. See page xx.

Protocol Functions

The

Protocols

feature is for setting up network options and parameters. It provides extensive access to NIC

parameters, and allows you to setup IP parameters (IP address, subnet mask, and default gateway). You can
enable/disable AppleTalk and NetWare, but not TCP/IP. (We recommend that you disable any protocol that you
are not using.)

Other Functions

Test Printer:

Click here, and then click on the

Start Test

button in the dialog box that appears, to send a test

document to the printer.

Configure Status Page:

Click here to configure Network Settings page options. In the dialog box that

appears, select the checkbox by

Print Status Page on Startup

to generate a status page (the Network Settings

page) each time you turn on the printer or reset the NIC.

note:

We recommend that you leave this setting checked to print at power-on.

To print out a Network Settings page immediately, click

Generate Now

.

Printer Status:

Click here to display status information for the printer and NIC, as well as errors and

messages.

«
...
77
78
79
80
81
...
»

Summary of Contents for Super Script 4400






























































































































































































































































































































Reviews:

No comments

Related manuals for Super Script 4400

Brand: Fenix Imvico Pages: 88

Brand: Radio Shack Pages: 62

Brand: Xerox Pages: 16

7760DN - Phaser Color Laser Printer

Brand: Xerox Pages: 6

Brand: Canon Pages: 36

Brand: Canon Pages: 62

WorkCentre 4260S

Brand: Xerox Pages: 8

Brand: Canon Pages: 738

Brand: Samsung Pages: 143

imageRUNNER 6570

Brand: Canon Pages: 274

Brand: Xerox Pages: 14

Brand: Xerox Pages: 2

Brand: Konica Minolta Pages: 15

Brand: Sagem Pages: 126

bizhub C452 Series

Brand: Konica Minolta Pages: 17

16C0365 - 5500 MFP

Brand: Lexmark Pages: 88

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Fast T-Jet Blazer Pro

Brand: Screen Print & Inkjet Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands