NEC Super Script 4400 Maintenance Manual Download Page 29 | Manualshive

Page: 29 / 317

background image

18

SuperScript 4400 — Maintenance Guide

S

UPER

S

CRIPT

4400 S

ETTINGS

Printer Settings

SuperScript 4400 printer settings give you many ways to customize your print job. There is often more than one
place to change the same printer setting. These include
•

The SuperScript PostScript 3 and PCL 5e printer drivers

•

The operator panel on your printer

Using the Printer Operator Panel

You can use the printer Operator Panel to cancel a print job or change settings that are not available in your printer
driver. You can view messages on the Operator Panel to help diagnose printing problems. In addition, the printer
operator panel allows you to print out font lists and test pages and view the total page count. You can also set the
printer’s TCP/IP address or reconfigure network settings. Chapter 4xx provides instructions for using the printer
operator panel.

Using Printer Drivers

Your printer software includes the PostScript 3 printer drivers for Windows 3.1x, Windows 95/98, Windows NT
4.0/5.0, and MacOS and the PCL 5e printer driver for Windows 3.1x, Windows 95/98, and Windows NT 4.0/5.0.
They offer a wide range of features for setting up your print job and printer settings.

Most of these features and settings are described in this chapter. A particular feature may be implemented slightly
differently, depending on which driver you are using.

note:

If you are unsure about a setting in your printer driver, be sure to use the driver’s Online Help feature.

Chapter xxx provides complete information about using your printer driver software.

When to Use the PostScript 3 or PCL 5e Printer Driver

Use the

PostScript 3

driver for color documents and documents that contain many complex graphic images or

extensive page layout formatting. The PostScript driver has more options and delivers better graphic processing.

Use the

PCL 5e

driver for monochrome documents that contain mostly text and limited formatting. The PCL5e

driver processes this type of document quickly.

note:

For color printing, you must use the PostScript 3 printer driver for your system. The PCL 5e printer driver

is for monochrome printing only.

«
...
27
28
29
30
31
...
»

Summary of Contents for Super Script 4400






























































































































































































































































































































Reviews:

No comments

Related manuals for Super Script 4400

Brand: DASCO Pages: 2

EasyCoder 501 SA

Brand: UBI Pages: 214

Brand: UBI Pages: 64

Brand: Xerox Pages: 9

Brand: Xerox Pages: 2

Brand: Xerox Pages: 8

Brand: Xerox Pages: 4

Brand: Xerox Pages: 150

Brand: Xerox Pages: 4

Brand: Xerox Pages: 6

Brand: Xerox Pages: 2

DocuPrint N2125

Brand: Xerox Pages: 246

DocuPrint N2025

Brand: Xerox Pages: 378

DocuPrint N2025

Brand: Xerox Pages: 176

DocuPrint C3290 FS

Brand: Xerox Pages: 240

Brand: Xerox Pages: 5

Brand: Xerox Pages: 7

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands