manualshive.com logo in svg

NEC Super Script 4400, Maintenance Manual

The NEC Super Script 4400 Maintenance Manual is the ultimate resource for managing and servicing your printer. This comprehensive manual, available for free download at manualshive.com, provides detailed instructions and troubleshooting tips to ensure optimal performance and extend the lifespan of your NEC Super Script 4400.

Share
Download
background image

5

To upgrade the 4400 Series boot code:

1.

Put the printer into service mode.

2.

From the operator panel, press Next  until 

BURN FLASH 

appears.

3.

Press Select  and 

FLASH BURN ‘SELECT’ ENTERS

 appears.

4.

Press Select  and 

FLASH BURN WAITING FOR DATA

 appears.

5.

From the computer, move to the directory containing the file for the new code or the installation program.
The file name for the new code is RELnnn.BDL where nnn is the upgrade version number. The file name for the 
installation program is PCADOBE.

6.

Use either the copy command or installation program to perform the upgrade.
•

To use the copy command, enter 

COPY /B REL

nnn.BDL LPT1:

 at the command prompt.

•

To use the installation program, enter 

PCADOBE <DIR> REL

nnn.BDL

 at the command prompt, where 

DIR

 is the path to 

REL

nnn.BDL

.

During the upgrade process, the operator panel will display the current status and any error messages. The 
process can take up to 2 minutes to complete.

If an error occurs, a message will appear on the operator panel. Repeat Step 4 through Step 6 if an error occurs. 
A list of error messages are shown in Appendix E.

Listed below is the sequence of messages that appear on the operator panel display during the upgrade 
process.

WAITING FOR DATA
DECODING DATA
STORING DATA
‘SELECT’ REBURNS

 (only displays for about 5 seconds during an unsuccessful upgrade)

‘MEDIA’ EXITS 

(indicates the end of the upgrade process)

7.

Turn the printer off and restart.

To upgrade the 4400 Series PS Code:

1.

Put the printer into service mode.

2.

From the operator panel, press Next  until 

DOWNLOAD CODE 

appears.

3.

Press Select  and 

WAITING FOR DATA 

appears.

4.

From the computer, move to the directory containing the file for the new code or the installation program.
The file name for the new code is SS44_nnn.CRN where nnn is the upgrade version number. The file name for 
the installation program is PCADOBE.

5.

Use either the copy command or installation program to perform the upgrade.
•

To use the copy command, enter 

COPY /B SS44_

nnn.CRN LPT1:

 at the command prompt.

•

To use the installation program, enter 

PCADOBE <DIR> SS44_

nnn.CRN

 at the command prompt, where 

DIR

 is the path to 

SS44_

nnn.CRN

.

During the upgrade process, the operator panel will display the current status and any error messages. The 
process can take up to 20 minutes to complete. If an error occurs, a message will appear on the operator panel 
display. A list of error messages are shown in Appendix E. Repeat Step 1 through Step 5 if an error occurs.

Listed below is the sequence of messages that appears on the operator panel display during the upgrade 
process.

WAITING FOR DATA
RECEIVING DATA
‘SELECT’ REBURNS

 (displays momentarily only during an unsuccessful upgrade)

DOWNLOAD CODE 

(indicates end of process)

6.

Turn off printer and restart it.

Summary of Contents for Super Script 4400






























































































































































































































































































































Reviews:

No comments

Related manuals for Super Script 4400

CAB A Series Programming Manual preview
A Series
Brand: CAB Pages: 263
Xerox All in One Printer Product Safety Data Sheet preview
All in One Printer
Brand: Xerox Pages: 3
V-King MK2 Assembly Manual preview
MK2
Brand: V-King Pages: 41
Xerox EX Printing Manual preview
EX
Brand: Xerox Pages: 40
QMS 2001 Setup Manual preview
2001
Brand: QMS Pages: 26
EasyThreed Mars Quick Start Manual preview
Mars
Brand: EasyThreed Pages: 15
MakerBot Replicator+ Reference Manual preview
Replicator+
Brand: MakerBot Pages: 48
Xerox AltaLink B8145 User Manual preview
AltaLink B8145
Brand: Xerox Pages: 418
Ricoh BOOKLET MAKER BK5010 Installation Manual preview
BOOKLET MAKER BK5010
Brand: Ricoh Pages: 74
Xerox 8200DX - Phaser Color Solid Ink Printer Manual preview
8200DX - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 2
Oki ES9160 MFP Manual preview
ES9160 MFP
Brand: Oki Pages: 182
Dremel DigiLab 3D40 FLEX Quick Start Manual preview
DigiLab 3D40 FLEX
Brand: Dremel Pages: 4
VOLUMIC STREAM MK3 Series User Manual preview
STREAM MK3 Series
Brand: VOLUMIC Pages: 70
Xerox ApeosPort C6550 I Network Administrator'S Manual preview
ApeosPort C6550 I
Brand: Xerox Pages: 132
Polaroid PLR-P3001-N User Manual preview
PLR-P3001-N
Brand: Polaroid Pages: 93
Xerox WORKCENTRE C2424 Service Manual preview
WORKCENTRE C2424
Brand: Xerox Pages: 432
Epson L380 User Manual preview
L380
Brand: Epson Pages: 144
Epson XP-8500 Series User Manual preview
XP-8500 Series
Brand: Epson Pages: 228

Brands by name

Popular brands

Load more brands