NEC Super Script 4400 Maintenance Manual Download Page 21

Page: 21 / 317

SuperScript 4400 — Maintenance Guide

NSTALLING

THE

PHOTOCONDUCTOR

BELT

MODULE

Make sure all packing materials and tape are removed from the printer.

Open the Front Cover of the printer by grasping in the Front Cover Release latch

(A)

Open the Top Cover of the printer by sliding the Top Cover Release button forward

(B)

Flip up the photoconductor belt module Locking Levers inside the printer

(C)

Remove the Tension Release Pins from both sides of the photoconductor belt module

(D)

Remove the black protective sheet from around the photoconductor belt module.

Slide the photoconductor belt module into the guides, as shown

(E)

. (The flat side of the module should face

the front of the printer.)

Snap the photoconductor belt module Locking Levers into place

(F)

Close the Top Cover and then the Front Cover of the printer.

note:

The photoconductor belt module is sometimes called the Photoconcuctor photoconductor belt module or

OPC Unit.

Caution

The photoconductor belt

module should slide easly into the
printer. Do not force it!

Summary of Contents for Super Script 4400






























































































































































































































































































































Search results

Summary of Contents for Super Script 4400

Reviews:

Related manuals for Super Script 4400

Brands by name

Popular brands

NEC Super Script 4400, Maintenance Manual

Search results

Summary of Contents for Super Script 4400

Reviews:

Related manuals for Super Script 4400

Brands by name

Popular brands