NEC Super Script 4400 Maintenance Manual Download Page 236 | Manualshive

Page: 236 / 317

background image

Imaging Artifacts

227

TROUBLESHOO

TING

14. Toner Drop -

Toner spot stain is caused on the print by the toner dropping within the printer engine.

Main Causes

1.

Toner drops on the transfer drum due to the break-down of the waste toner feeder's drum cleaner.
a. Mylar of the waste toner feeder is deformed.
b. Waste toner is not properly collected by the waste toner feeder.

2.

Toner adhering to the developer roller drops on the photoconductor belt.

Countermeasures

1.

Check up the cleaning brush and waste toner feeder.
a. Clean the perimeter of the cleaning brush installation location.
b. Check the seal for damage. If damaged, replace the waste toner feeder with a new feeder.
c. Check for waste toner in the printer. If so, vacuum the waste toner with a toner vacuum cleaner.

2.

Remove the toner module.
a. Clean the surface of developer roller.
b. Replace the toner module with a new module.

Cleaning Brush

Cleaning Roller

Waste Toner
Feeder

Transfer Drum

Developer Roller

Toner Drop

Toner Module

«
...
234
235
236
237
238
...
»

Summary of Contents for Super Script 4400






























































































































































































































































































































Reviews:

No comments

Related manuals for Super Script 4400

Brand: Samsung Pages: 82

Brand: Samsung Pages: 2

Brand: TASKalfa Pages: 36

Brand: Xerox Pages: 44

Brand: Oki Pages: 76

Brand: Oki Pages: 28

Brand: Oki Pages: 22

image RUNNER 3045

Brand: Canon Pages: 14

Brand: Oki Pages: 512

4150S - WorkCentre B/W Laser

Brand: Xerox Pages: 4

Brand: Olivetti Pages: 74

Brand: Xerox Pages: 14

Brand: Xerox Pages: 13

Brand: ABLE Systems Pages: 4

Brand: Me3D Pages: 14

8200DX - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 2

Brand: Konica Minolta Pages: 3

Brand: Rimage Pages: 217

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands