NEC Super Script 4400 Maintenance Manual Download Page 72

Page: 72 / 317

CHAPTER 5

NETWORK PRINTING

NETWORK SETUP

To begin using the SuperScript 4400 Printer as a network printer, you must do the following setup tasks.

Connect the 4400N to your network (see page 23).

note:

The 4400N printer already has a network interface card (NIC) installed. If you have a 4400 printer, you can

purchase a Network Interface Upgrade Kit and install a NIC yourself. See page 27 for installation instructions.

Assign an IP address to the 4400N printer. (This step is not necessary for Mac OS users.)

Configure your network and workstations to use the 4400 network printer.

This Chapter contains the following sections
•

Network Printer Features

•

Network Administration Page

•

Using MAP

•

Windows TCP/IP Setup

•

Windows Peer to Peer Printing

•

lpr Printing Setup in Windows NT

•

Windows 95/98 Shared Printing Setup

•

DHCP

•

NetWare 4.x Setup

•

NetWare 3.x Setup

•

Web JetAdmin

•

UNIX Setup

Summary of Contents for Super Script 4400






























































































































































































































































































































Search results

Summary of Contents for Super Script 4400

Reviews:

Related manuals for Super Script 4400

Brands by name

Popular brands

NEC Super Script 4400, Maintenance Manual

Search results

Summary of Contents for Super Script 4400

Reviews:

Related manuals for Super Script 4400

Brands by name

Popular brands