manualshive.com logo in svg

NEC Super Script 4400, Maintenance Manual

The NEC Super Script 4400 Maintenance Manual is the ultimate resource for managing and servicing your printer. This comprehensive manual, available for free download at manualshive.com, provides detailed instructions and troubleshooting tips to ensure optimal performance and extend the lifespan of your NEC Super Script 4400.

Share
Download
background image

248

SuperScript 4400 — Maintenance Guide

1. Ensure the outlet is at the correct voltage
    and amperage for the printer.
2. Replace the Fuser Unit with the correct unit.

3. Connect it properly.

4. Re-install Fuser Unit.

5. 

Replace the connector.

6. Replace the lamp and lamp holder.
7. Replace the heater.

8. Replace the Low Voltage Power Supply 
    Unit (LVPS). 
9.Replace MCTL PWB 

H0

Code

Description of Error

Cause of Error

Clearance Method

Fuser Unit and Others

H2,
H3,
H4

1. 

Input voltage

2. Fuser Voltage Rating
    (110 or 220)
3. HP/HN connector not
    connected
4. Fuser Unit improperly 
    installed
5. Fuser connector 
    damaged
6. Lamp Holder contract failure
7. Heater wiring cut or 
    damaged
8. Low Voltage Power Supply 
    Unit (LVPS) Failure
9. MCTL PWB Failure

Fuser Unit

1. Fuser Improperly 
    Installed
3. C

ontact failure due to 

     damaged connector of fuser 
     unit

4. 

Loose/Broken connection

5. Defective Fuser Unit
6. IOD1 Failure
7. MCTL PWB Failure

1. Re-installe fuser unit.

3. Replace fuser unit.

4. Check the connection between 

the fuser unit

    and BCN2 of the high voltage unit (HVU)

5. Replace fuser unit.
6. 

Replace 

the IOD1

 P.W.B. 

7.Replace MCTL PWB 

(wire
 cut/ 
short
error
of ther-
mistor)

MCTL

11CN

42
44

TH1
TH2

IOD1

DCN1 DCN14

HVU

42
44

TH1
TH2

BCN2

TH2

TH1

16
18

16
18

Fuser Unit

Fuser Connector

1
2

3
4

Summary of Contents for Super Script 4400






























































































































































































































































































































Reviews:

No comments

Related manuals for Super Script 4400

3D Systems CubePro Setup And Repacking Manual preview
CubePro
Brand: 3D Systems Pages: 26
3D Systems CubePro Repair Manual preview
CubePro
Brand: 3D Systems Pages: 39
3D Platform WorkSeries 200 Series Quick Reference Manual preview
WorkSeries 200 Series
Brand: 3D Platform Pages: 9
A&D MCP1000 Series Instruction Manual preview
MCP1000 Series
Brand: A&D Pages: 16
Oce DFS10 Operator'S Manual preview
DFS10
Brand: Oce Pages: 90
Xante FilmMaker 4 Quick Reference Manual preview
FilmMaker 4
Brand: Xante Pages: 31
Xerox EC8056 Getting Started preview
EC8056
Brand: Xerox Pages: 13
Xerox DocuPrint 205 Settings Manual preview
DocuPrint 205
Brand: Xerox Pages: 34
Citizen CT-D101 User Manual preview
CT-D101
Brand: Citizen Pages: 57
Lanier GX3050N Brochure preview
GX3050N
Brand: Lanier Pages: 4
Panduit PTR3E Operator And Technical Reference Manual preview
PTR3E
Brand: Panduit Pages: 59
Xante ColourLaser 21 Series Setup Manual preview
ColourLaser 21 Series
Brand: Xante Pages: 32
Epson All in One Printer User Manual preview
All in One Printer
Brand: Epson Pages: 210
Epson aculaser cx37 series User Manual preview
aculaser cx37 series
Brand: Epson Pages: 261
Epson AL-MX200 Series User Manual preview
AL-MX200 Series
Brand: Epson Pages: 410
Epson AcuLaser CX29DNF User Manual preview
AcuLaser CX29DNF
Brand: Epson Pages: 456
Epson AL-MX300 Series Quick Start Manual preview
AL-MX300 Series
Brand: Epson Pages: 2
Epson Stylus C42 Series Printer Basics Manual preview
Stylus C42 Series
Brand: Epson Pages: 59

Brands by name

Popular brands

Load more brands