NEC SL1100 Features And Specifications Manual Download | Manualshive

Page: 775 / 864

background image

Conditions

• You can assign up to 32 IP Terminals in an Internal or All call paging group.
• When using Unicast mode, there must be an available DSP recourse for each IP Terminal in the

page group at the time of the internal page. If the resources are less than the number of IP
Terminals, the page will be delivered to the IP Terminals with the lowest port numbers. IP Terminals
that cannot obtain a DSP resource will not receive the page.

• IP Terminals via NAT cannot utilize Multicast paging. These terminals must use Unicast paging.
• The ability to assign Unicast or Multicast on an IP Terminal basis, is restricted to internal paging

only. Other Multicast features (External MOH, Background Music, Room Monitor) cannot utilize
Unicast.

• For an IP Terminal to utilize the Multicast feature the IP Terminal must have a gateway programmed

to accomplish the multicast transmission. When an actual gateway device does not exist on the
network, a dummy gateway address on the same subnet must be defined.

• When utilizing Multicast mode and a page group consists of all IP Terminals, the page is sent via a

multicast message from the initiating phone. If a paging group has IP and TDM Terminals, when an
IP Terminal initiates the page, a message is sent to the VoIPDB and the VoIPDB sends the
Multicast message for the IP Terminals.

• When using the G.711 Codec for multicast paging, only 10ms, 20ms, 30ms, and 40ms frame sizes

can be used.

Default Settings

Multicast

System Availability

Terminals

All IP Terminals

Required Component(s)

IP Terminal

CPU and IP4WW-VOIPDB-C1

Router that supports Multicast Packets if utilizing Multicast Mode

Related Features

IP Multiline Station (SIP)

Meet Me Paging

Meet Me Paging Transfer

Paging, External

Paging, Internal

ISSUE 2.0

SL1100

Features and Specifications Manual

1-763

U

«
...
773
774
775
776
777
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: Retekess Pages: 9

Brand: Aiwa Pages: 46

Brand: Zonex Pages: 28

Brand: ClearOne Pages: 48

Brand: vistaCNC Pages: 7

WX-C1011 Series

Brand: Panasonic Pages: 18

WGAV120 - VIDEO TRANSMISSION

Brand: Panasonic Pages: 40

VoiceSonic KX-NT700

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

WXC3010 - CENTER MODULE - MULTI LANGUAGE

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 408

Brand: Panasonic Pages: 554

Brand: Sony Pages: 36

JumboTron JTC-C200

Brand: Sony Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands