NEC SL1100 Features And Specifications Manual Download | Manualshive

Page: 688 / 864

background image

SIP Trunk E.164 Support

(This feature is for V2.0 or higher)

Description

With the SIP Trunk E.164 Support enabled the PBX is able to support SIP configurations where the
number presentation within the SIP messages is formatted using the E.164 international numbering
scheme. Specifically the system is able to handle the ‘+’ digit when required as the International
Access Code.

For example a normal international SIP call could be dialed and presented from the system as follows;
Number dialed =

00441202223344

Request-URI: Invite sip:[email protected] SIP/2.0

However with SIP Trunk E.164 Support enabled the SIP call could be presented once dialed as below;

Request-URI: Invite sip:[email protected] SIP/2.0

This presentation can be a requirement of certain SIP ITSPs (Internet Telephony Service Providers)
so it is necessary the PBX can handle these calls and modify any SIP messages to the correct format
accordingly.

Below is the full list of SIP header fields used by this feature:

Request-URI
To
From
P-Asserted Identity
P-Preferred Identity

Conditions

• E.164 support is applied on the SIP trunk interface.
• E.164 is supported for all carrier choices (PRG 10-29-14).
• SL Net multi-carrier support will apply E.164 support across all carrier configurations at secondary

nodes.

Default Settings

Disabled

System Availability

Trunks

IP SIP

Required Component(s)

• VoIPDB C1

SL1100

ISSUE 2.0

1-676

SIP Trunk E.164 Support

S

«
...
686
687
688
689
690
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: Xtrons Pages: 11

Brand: fadini Pages: 12

VideoJet 400 19"

Brand: VCS Pages: 86

Brand: BFT Pages: 68

Brand: Kenwood Pages: 160

Blade Extreme BLX12DVC

Brand: Boss Audio Systems Pages: 1

TOSVERT VF-AS1 Series

Brand: Toshiba Pages: 13

Brand: Toshiba Pages: 317

IntelliSync 523404

Brand: Pentair Pages: 2

PENTEK DEFENDER CSC-LINK

Brand: Pentair Pages: 28

Brand: Pentair Pages: 32

Brand: RCA Pages: 10

Brand: Victron energy Pages: 63

Brand: Garmin Pages: 4

Brand: Audio enhancement Pages: 3

Brand: Döhmann Pages: 21

Brand: Roth Audio Pages: 16

Brand: Factor Electronics Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands