Home
/
NEC
/
SL1100
/
Features And Specifications Manual

NEC SL1100, Features And Specifications Manual

Share

Page: 123 / 864

NEC SL1100 Features And Specifications Manual Download Page 123

Guide to Feature Programming

The programs listed below indicate the most commonly used programs required for this feature. The
programs are listed in the order that the installer should follow. Refer to the PCPro wizards for further
detailed programming.

• When a * is listed next to the Program Number it indicates a program that

MUST

be set (from a

default state) for this feature to be enabled.

Call Waiting

Program

Number

Program Name/Description

Assigned Data

15-02-12

Off Hook Ringing

Per Station use this option to set the telephone Off-Hook signaling
type that occurs when a user receives a second call while busy on a
handset call.

0 = Muted Off-Hook Ringing
1 = No Off-Hook Ringing
3 = Beep in Speaker
4 = Beep in Handset
5 = Beep in Speaker and Handset
(default = 0)

20-09-01

Second Call for DID/DISA/DIL/E&M

This option enables or disables a users ability to receive a second call
from a DID, DISA, DIL, or E&M Tie line per class of service (PRG
20-06-01).

0 = Off

(2nd call will not be allowed.)

1 = On

(2nd call is allowed.)

(default = 1)

20-09-07

Call Queuing

This option enables or disables a users ability to have calls queued if
a call rings the extension when it is busy.

0 = Off

(Calls are not queued.)

1 = On

(Calls are queued.)

(default = 1)

20-13-05

Intercom Off Hook Signaling

This option enables or disables a users ability to receive off hook sig-
nals.

0 = Off

(ICM off hook signaling disa-

bled.)

1 = On

(ICM off hook signaling ena-

bled.)

(default = 1)

20-13-06

Automatic Off Hook Signaling

This option enables or disables the users ability to manually or auto-
matically receive off hook signals.

0 = Off

(manually)

1 = On

(automatically)

(default = 1)

20-18-06

Interval of Call Waiting Tone

This program allows you to adjust the time between call waiting/off
hook signaling tones.

0 ~ 64800 = 0 ~ 64800 seconds
(default =10 seconds)

Below is a chart that shows setting data for certain call waiting scenarios.

Busy Signal:

No call forwarding

Ring Back Signal:

Caller queues at called

Station

Busy forwarding imme-

diately upon Busy

Internal Call to

Station on Inter-

nal Call

20-09-07 = Off
20-13-06 = Off
24-09-05 = Off

20-13-06 = On

*1

20-09-07 = Off
20-13-06 = Off
24-09-05 = On

Station on Trunk

call

20-09-07 = Off
20-13-06 = Off

24-09-05 = Of

20-13-06 = On

*1

20-09-07 = Off
20-13-06 = Off
24-09-05 = On

DID Call to

Station on Inter-

nal Call

20-09-01 = Off
20-09-07 = Off
24-09-04 = Off

20-09-01 = On
20-09-07 = On

20-09-01 = Off
20-09-07 = Off
24-09-04 = On

Station on Trunk

Call

20-09-01 = Off
20-09-07 = Off
24-09-04 = Off

20-09-01 = On
20-09-07 = On

20-09-01 = Off
20-09-07 = Off
24-09-04 = On

ISSUE 2.0

SL1100

Features and Specifications Manual

1-111

C

«
...
121
122
123
124
125
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands