NEC SL1100 Features And Specifications Manual Download | Manualshive

Page: 132 / 864

background image

Redial Menu

Incoming
History

= Press Left Cursor key

Once the LEFT key is pressed, the Right Cursor
key can be used to switch between the Redial
and Incoming History menus.

Figure 1-2 Left Cursor Key Operation Flow Chart

Cursor Key Operation (When set PRG 15-02-60: 1 or 2)

Pressing the

Left Cursor

key displays the Received Call History.

Caller ID Digits to Voice Mail

A Caller ID trunk can send Remote Log-On Protocol with Caller ID digits to the voice mail. When a
trunk 001 receives the Caller ID as 12345, the protocol becomes

***

60001

*

12345

*

.

Outputting Caller ID Data

The system includes the Caller ID data on the SMDR report. The report provides the incoming call DN
in the DIALED NUMBER field. The CLASS field shows PIN (just like all other incoming calls).

Display Reason for No Caller ID Information

With Caller ID enabled, the system provides information for analog calls that do not detect the Caller
ID information. If the Caller ID information is restricted, the telephone display shows PRIVATE. If the
system cannot provide Caller ID information because Telco information is not detected, the display
shows NO CALLER INFO.

Option to Enable Caller ID Name for SLT

System programming provides an option for Single Line Terminals to display Caller ID.

Caller ID Sender Queuing Added

The SL1100 system can provide Caller ID (calling party number) to a Single Line Terminal with a
display.

The system can queue incoming calls to the Single Line Terminal if the system Caller ID sender
resources are busy. Refer to PRG 20-19-05 in the

SL1100 Programming Manual

.

If the Single Line Terminal user lifts their handset while an incoming call is waiting in queue, they hear
silence (no dial tone) and cannot dial out. When the Single Line Terminal user goes back on-hook, the
system immediately sends the queued call to the Single Line Terminal without Caller ID.

Conditions

• To have pre-answer Caller ID from the voice mail, the call must be an unscreened transfer.
• Caller ID is provided by the CPU. The EXIFE, which plugs into the KSU, can provide additional

resources for Caller ID if needed.

• Caller ID Name can display up to 12 characters.
• Caller ID Number can display up to 11 numbers.
• A Caller ID Number with more than 12 digits follows PRG 20-19-01 (first 10 or the last 10 digits).
• Caller ID information can be stored in Speed Dialing or One-Touch bins.
• Caller ID can be displayed for incoming calls and transferred calls.
• ARS can block outgoing Caller ID information on a call-by-call basis. To do this, insert the Caller ID

block code (e.g., .141) in the ARS Dial Treatments.

SL1100

ISSUE 2.0

1-120

Caller ID

C

«
...
130
131
132
133
134
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: Alpine Pages: 16

Brand: Aiwa Pages: 20

Brand: YARMEE Pages: 7

PNOZ m ES CC-Link

Brand: Pilz Pages: 24

Brand: Shure Pages: 18

Brand: Stahl Pages: 24

Clementine 8440

Brand: PNI Pages: 8

Audio 30 Export 3301

Brand: Becker Pages: 92

Brand: Barco Pages: 124

Brand: Crestron Pages: 26

Brand: Imesa Pages: 33

Brand: Roadstar Pages: 21

Brand: Elenberg Pages: 36

Brand: Emerson Pages: 16

Brand: Emerson Pages: 2

Brand: Emerson Pages: 8

Brand: Emerson Pages: 28

Brand: Emerson Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands