manualshive.com logo in svg

NEC SL1100, Features And Specifications Manual

The NEC SL1100 user manual is a comprehensive guide designed to assist users in understanding and operating their SL1100 phone system. Easily accessible for download, the manual offers step-by-step instructions, troubleshooting tips, and valuable insights to maximize the full potential of the SL1100. Get it for free at manualshive.com.

Share
Download
background image

IP Trunk - (SIP) Session Initiation Protocol

Version 2.0 or higher software provides;

• When + is added to the country code of an incoming SIP trunk call, it is recognized as an

international call, simplifying outgoing calls from the incoming call list.

Description

The SL1100 IP Trunk SIP package sends the real time voice over the corporate LAN or WAN. The
voice from the telephone is digitized and then put into frames to be sent over a network using Internet
protocol.

Using VoIPDB equipment at a gateway (a network point that acts as an entrance to another network),
the packetized voice transmissions from users in the company are received and routed to other parts
of the company Intranet (local area or wide area network) or they can be sent over the Internet using
CO lines to another gateway.

Depending on the requirements and resource allocation in the LAN/WAN/Internet, the VoIPDB - SIP
can be configured to use any of the following voice compressions:

• G.711 μ-Law - Highest Bandwidth
• G.729 (a) - Most often used
• The LAN/WAN or Internet connection is provided by a 10 Base-T/100 Base-TX Ethernet.

For a list of vendors that have successfully completed interoperability certification go to 

http://

www.necntac.com

 and refer to Technical Documentation.

SIP Trunk E.164 Support (V2.0 or higher)

With the SIP Trunk E.164 Support enabled the PBX is able to support SIP configurations where the
number presentation within the SIP messages is formatted using the E.164 international numbering
scheme. Specifically the system is able to handle the ‘+’ digit when required as the International
Access Code.

For example a normal international SIP call could be dialed and presented from the system as follows;
Number dialed = 

00441202223344

Request-URI: Invite sip: [email protected] SIP/2.0

However with SIP Trunk E.164 Support enabled the SIP call could be presented once dialed as below;

Request-URI: Invite sip:[email protected] SIP/2.0

This presentation can be a requirement of certain SIP ITSPs (Internet Telephony Service Providers)
so it is necessary the PBX can handle these calls and modify any SIP messages to the correct format
accordingly.
Below is the full list of SIP header fields used by this feature:
Request-URIToFromP-Asserted IdentityP-Preferred Identity

SIP Trunk E.164 CLIP Enhancement (V2.0 or higher)

With the SIP Trunk E.164 CLIP Enhancement enabled, when an incoming SIP call from an external
ITSP is presented at the system with a “+” in the From header field as the international access code, it
is recognized and displayed as an international call at the terminal display and also logged in the
terminals incoming caller history, allowing any outbound calls made from a multiline terminals caller
history possible using this numbering scheme.

This presentation can be a requirement of certain SIP ITSPs (Internet Telephony Service Providers)
so it is necessary the PBX can handle these calls and modify any SIP messages to the correct format
accordingly.

SL1100

ISSUE 2.0

1-452

IP Trunk - (SIP) Session Initiation Protocol

I

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

NEC ElectraElite IPK Installation And Maintenance Manual preview
ElectraElite IPK
Brand: NEC Pages: 20
Bang & Olufsen BeoSound 4 Supplement Manual preview
BeoSound 4
Brand: Bang & Olufsen Pages: 6
Bang & Olufsen BeoSound 5 Encore Manual preview
BeoSound 5 Encore
Brand: Bang & Olufsen Pages: 25
Bang & Olufsen BeoCenter 2 Manual preview
BeoCenter 2
Brand: Bang & Olufsen Pages: 28
Fancom LUMINA 41 Instruction Manual preview
LUMINA 41
Brand: Fancom Pages: 51
DC-Connex DCX-313 Quick Start Manual preview
DCX-313
Brand: DC-Connex Pages: 16
Yetter AIR ADJUST 2940 Operator'S Manual preview
AIR ADJUST 2940
Brand: Yetter Pages: 64
FOUR MP100BTi Owner'S Manual preview
MP100BTi
Brand: FOUR Pages: 28
Kraken Acoustics Active 3 User Manual preview
Active 3
Brand: Kraken Acoustics Pages: 12
Fusion FUS-SW104 User Manual preview
FUS-SW104
Brand: Fusion Pages: 4
FM 90.0010.60 Operating Instructions Manual preview
90.0010.60
Brand: FM Pages: 16
Daewoo AGC-2208RDS Service Manual preview
AGC-2208RDS
Brand: Daewoo Pages: 21
Blaupunkt 7 645 261 310 Operating Instructions Manual preview
7 645 261 310
Brand: Blaupunkt Pages: 36
Paso PM2094-V Instructions For Use Manual preview
PM2094-V
Brand: Paso Pages: 8
Aritech RF-4041-07-2 Installation Sheet preview
RF-4041-07-2
Brand: Aritech Pages: 18
Vicon Origin Setup And Maintenance Manual preview
Origin
Brand: Vicon Pages: 44
Aritech CS-152 User Manual preview
CS-152
Brand: Aritech Pages: 28
Philips FW-C90 Specifications preview
FW-C90
Brand: Philips Pages: 2

Brands by name

Popular brands

Load more brands