NEC SL1100 Features And Specifications Manual Download | Manualshive

Page: 477 / 864

background image

Fractional PRI

Program

Number

Program Name/Description

Assigned Data

10-39-01 *

Fractional Setup

This program is used to enable/disable the SL1100's ability to use a
fractional PRI or T1.

0 = Disable

(when disabled the sys-

tem will assign the PRI as a full PRI
and use 24 trunks.)

1 = Enable

(when enabled the sys-

tem will not assign any trunks to the
PRI, the trunks must be manually
configured.)

(default = 0)

10-03-21 *

Number of Ports

This program assigns the number or ports to the PRI card when PRG
10-39-01 is set to a 1 (fractional enabled).
After this program is changed the PRI card must be reset before the
system will assign trunks to the PRI.

0 = Automatic
1 = 4 Ports
2 = 8 Ports
3 = 12 Ports
4 = 16 Ports
5 = 20 Ports
(default = 0)

Calling Party Number Presentation (CPN)

Program

Number

Program Name/Description

Assigned Data

20-08-13 *

ISDN CLIP

This program enables/disables the ability to send calling party number
information per class of service.

0 = Off

(when set to Off the system

will not send any outbound calling
party information.)

1 = On

(when set to ON the system

will send calling party information for
the station or trunk.)

(default = 0)

21-12-01 *

ISDN CPN setup for Trunks

This program is used to assign a calling party number per trunk.
If CPN information is programmed on both the trunk and station when
a call is made the CPN from the station will be sent to the Telco.

Maximum of 16 digits

(0 ~ 9,

*

, #)

Most Telco's will only accept 10
digits.

(default = Not Assigned)

21-13-01 *

ISDN CPN setup for Stations

This program is used to assign a calling party number per station.
If CPN information is programmed on both the trunk and station when
a call is made the CPN from the station will be sent to the Telco.

Maximum of 16 digits

(0 ~ 9,

*

, #)

Most Telco's will only accept 10
digits.

(default = Not Assigned)

10-03-05

ISDN Clip Information

This program allows/denies the sending of calling party number infor-
mation per PRI.

0 = NO

(CPN is NOT sent.)

1 = YES

(CPN is sent.)

(default = 1)

15-01-04

ISDN Caller ID

This program allows/denies the sending of calling party number infor-
mation per station.

0 = Disabled

(CPN is NOT sent.)

1 = Enabled

(CPN is sent.)

(default = 1)

15-07-01

Programmable Function Keys

This program is used on a per station basis to assign different function
keys to the Multiline Terminals.
Function key (63) is used to temporarily block the station from sending
CPN information. When the key is pressed it will light up red and while
the key is lit any calls from that station will not send CPN information
to the Telco.

63 = Outgoing Call Without Caller
ID
(Refer to the programming manual for
the default values and for all other
available options in this command.)

ISSUE 2.0

SL1100

Features and Specifications Manual

1-465

I

«
...
475
476
477
478
479
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: Panasonic Pages: 3

Brand: Harman Pages: 10

AZ8350 - Cd Radio Cass Recorder

Brand: Magnavox Pages: 18

Brand: Akura Pages: 11

Brand: THOMSON Pages: 81

BeoSound 3000 2671

Brand: Bang & Olufsen Pages: 68

Brand: 2VV Pages: 29

Brand: Yealink Pages: 52

Brand: Parker Pages: 47

Brand: T-audio Pages: 2

Brand: Fender Pages: 51

Brand: Prology Pages: 37

Brand: Clas Ohlson Pages: 36

Brand: Vitek Pages: 28

AQUACIAT POWER LD 602R-3500R

Brand: CIAT Pages: 56

Brand: Champion Pages: 46

Brand: Hitachi Pages: 242

SAAK66 - MINI HES W/CD PLAYER

Brand: Panasonic Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands