NEC SL1100 Features And Specifications Manual Download | Manualshive

Page: 475 / 864

background image

• Calling Party Number (CPN) presentation from station is available for virtual extensions.
• The trunk setting (PRG 20-19-09) for sending the caller name on outgoing ISDN calls takes priority

over the same setting for the station (PRG 15-01-01).

• When programmed, Calling Party Name will be sent on calls that originate from a station (MLT, SLT,

or IP Multiline) or an incoming trunk (Analog or ISDN).

• Calling Party Name supports up to 12 ASCII characters.
• When a call originates from a virtual extension, the Calling Party Name for the virtual extension is

sent. It does not follow the setting in PRG 15-18-02.

• Calling Party Name is dependant upon the carrier. The network carrier must allow the SL1100 to

edit the Calling Party Name information.

• SL1100 does not support ISDN sub-addressing.

Default Settings

None

System Availability

Terminals

Not Applicable

Required Component(s)

To provide ISDN-PRI trunk connection:

• 1PRIU-C1

Related Features

Central Office Calls, Answering

Central Office Calls, Placing

Direct Inward Dialing (DID)

Direct Inward Line (DIL)

Forced Trunk Disconnect

Station Message Detail Recording

Transfer

Guide to Feature Programming

The programs listed below indicate the most commonly used programs required for this feature. The
programs are listed in the order that the installer should follow. Refer to the PCPro wizards for further
detailed programming.

• When a * is listed next to the Program Number it indicates a program that

MUST

be set (from a

default state) for this feature to be enabled.

ISSUE 2.0

SL1100

Features and Specifications Manual

1-463

I

«
...
473
474
475
476
477
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: Samsung Pages: 42

Brand: Barco Pages: 2

Brand: Measurement Computing Pages: 32

Brand: Polycom Pages: 36

Brand: Jensen Pages: 13

Brand: Digitrax Pages: 8

Brand: Oak Telecom Pages: 43

Brand: Rath Pages: 7

Brand: ICON Pages: 6

Brand: GRS Pages: 4

Happy Call Series

Brand: lee handels Pages: 13

Brand: T+A Pages: 70

Brand: Magnavox Pages: 1

Brand: Daewoo Pages: 31

Brand: iPECS Pages: 101

Brand: RCA Pages: 68

Brand: btsr Pages: 129

Brand: Honeywell Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands