NEC SL1100 Features And Specifications Manual Download

Page: 295 / 864

Program

Number

Program Name

Default

Note

11-11-35

Service Code Setup (for Setup/Entry Operation) - Pi-
lot Group Withdrawing

650

11-11-36

Service Code Setup (for Setup/Entry Operation) -
Toll Restriction Override

663

11-11-37

Service Code Setup (for Setup/Entry Operation) -
Ring Volume Set

729

11-11-38

Service Code Setup (for Setup/Entry Operation) -
Programmable Function Key Programming (3-Digit
Service Codes)

752

11-11-39

Service Code Setup (for Setup/Entry Operation) -
Station Speed Dial Number Entry

755

11-11-41

Service Code Setup (for Setup/Entry Operation) -
Tandem Ringing

not assigned

11-11-42

Transfer Dial Setting for Out of Range

689

11-11-43

Service Code Setup (for Setup/Entry Operation) -
Headset Mode Switching

688

11-11-45

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward All (Split)

682

11-11-46

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward Busy (Split)

683

11-11-47

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward No Answer (Split)

684

11-11-48

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward Busy No Answer (Split)

685

11-11-49

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward Both Ring (Split)

686

11-11-50

Service Code Setup (for Setup/Entry Operation) - Set
Message Waiting Indication

not assigned

11-11-51

Service Code Setup (for Setup/Entry Operation) -
Cancel Message Waiting Indication

not assigned

11-11-52

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward All Destination (No Split)

790

11-11-53

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward Busy Destination (No Split)

791

11-11-54

Service Code Setup (for Setup/Entry Operation) -
Set/Cancel Call Forward No Answer Destination (No
Split)

792

11-11-55

Service Code Setup (for Setup/Entry Operation) -
Call Forward Busy No Answer Destination (No Split)

793

11-11-58

Service Code Setup (for Setup/Entry Operation) -
Call Forward with Personal Greeting

713

11-11-59

Call Forward to Attendant except Busy

696

11-11-60

Call Forward to Attendant/No Answer

697

11-11-62

Adjust of Headset Ring Volume

not assigned

11-11-65

Headset Mode Switching

not assigned

11-11-68

Service Code Setup (for Setup/ Entry Operation) - In-
traMail Language Selection for own Extension

664

11-11-69

Service Code Setup (for Setup/ Entry Operation) - In-
traMail Language Selection for Specific Extension

665

11-11-70

Backlight Brightness

705

11-11-71

Auto Backlight

706

11-11-72

Headset V.Announce

714

ISSUE 2.0

SL1100

Features and Specifications Manual

1-283

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SL1100

Reviews:

Related manuals for SL1100

Brands by name

Popular brands

NEC SL1100, Features And Specifications Manual

Search results

Summary of Contents for SL1100

Reviews:

Related manuals for SL1100

Brands by name

Popular brands