NEC SL1100 Features And Specifications Manual Download | Manualshive

Page: 145 / 864

background image

Caller ID Refuse for "Private" Numbers

Program

Number

Program Name/Description

Assigned Data

14-01-27 *

Caller ID Refuse Setup

Per trunk enable or disable the ability to use the caller ID refuse fea-
ture.

0 = Disable

(CID refuse will not func-

tion.)

1 = Enable
(default = 0)

22-18-01

Private Call Assignment Setup - Transfer Mode

Leave this program set to (

0

) Not Defined to route the Private caller to

a VRS message to refuse the call.
This program can also be used to route the Private caller to an inter-
nal destination (PRG 22-18-02) or a Ring Group (PRG 22-04).

0 = Not Defined

(Private call will not

transfer to a user in the system, can
be routed to VRS message in PRG
40-10-06.)

1 = Internal Dial

(Specified in PRG

22-18-02)

2 = Incoming Ring Group

(Specified

in PRG 22-04)

(default = 0)

40-10-06 *

Set VRS Message for Private Call Refuse

This program specifies the VRS message to be played to the caller
when the Private Call Refuse feature is activated.
If VRS Fixed Message is enabled (PRG 40-10-01), a setting of (

101

)

will play the following message to the caller: "Your call cannot go
through".

0 = No Message Played
1 ~ 100 = VRS Message 1 ~ 100
101 = VRS Fixed message

(Mes-

sage will only play if PRG 40-10-01 is
enabled.)

(default = 0)

15-07-01

Programmable Function Keys

This program is used on a per station basis to assign different function
keys to the Multiline Terminals.
Function key (

86

) is the Private Call Refuse key. This key is used to

enable or disable the Private Call Refuse feature. When enabled all
Private numbers received will be routed to the VRS message speci-
fied in PRG 40-10-06.
The feature can be enabled or disabled by using this key or by enter-
ing a service code.

86 = Private Call Refuse
(Refer to the programming manual for
the default values and for all other
available options in this command.)

11-10-32

Set Private Call Refuse

This program is used to assign the service code to enable or disable
the Caller ID Refuse feature.
The service code assigned must be within your valid numbering plan
in PRG 11-01-01.

Maximum of 8 digits

(0 ~ 9,

*

, #)

(default = 646)

20-07-24

Set/Cancel Private Call Refuse

Per class of service (PRG 20-06-01) this program is used to allow or
deny the stations ability to set or cancel the Private Call Refuse fea-
ture.

0 = Off

(User cannot control the fea-

ture.)

1 = On
(default = 1)

The Caller ID - Flexible Ringing Flowchart below helps define programming:

ISSUE 2.0

SL1100

Features and Specifications Manual

1-133

C

«
...
143
144
145
146
147
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

CQ-C7413U? CQ-C7113U

Brand: Panasonic Pages: 22

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

PowerVIEW HD-30

Brand: VADDIO Pages: 24

Brand: jWIN Pages: 13

Brand: Jensen Pages: 41

Brand: Micronix Pages: 16

Aeware in.k100 Series

Brand: Gecko Pages: 10

TALENT STATION TS-4

Brand: Wheatstone Pages: 33

Brand: Scott Pages: 29

Brand: TechniSat Pages: 24

Brand: Mi-Light Pages: 5

Pilot Lite V1522

Brand: Vicon Pages: 138

Brand: AudioBahn Pages: 13

Pressman TCM-5000EV

Brand: Sony Pages: 2

MV-900SDS - Dream System 3

Brand: Sony Pages: 2

Brand: Sony Pages: 22

Pressman TCM-5000EV

Brand: Sony Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands